- Analyze the track plan and create all possible routes automatically.
- Sets the routes field in tracks, signals and sensors → route representation.
- The direction track can be used to restrict a route generation only in that direction.
- The Connector can be used to connect distant elements
- Turnout commands are added to the route.
- Signal pair selection.
- Module support.
- Fiddle Yard support.
- Road plans are partly supported.
- Not all 'weird' situations are recognised.
Note: The Analyzer was introduced as a tool especially for the new and inexperienced user allowing for quick access to fully automated model railroading.
However, with complex or unusual layouts the Anlyzer may fail to generate all routes possible or it may generate unexpected routes or in worst case it may even hang.
In all these cases settings have to be adjusted or completed by hand while those routes generated correctly by the Analyzer can serve as a blueprint.
- Track plan must be healthy before analyzing!
- Activated option Use block side routes in the Rocrail automatic tab.
- All items must be connected without a space in between them. Exception: The Connector
- Only one item at one position in the plan is allowed. (No overlapping.)
The Analyzer can be activated manually.
The feature is started manually by
- either entering z in the Rocrail server terminal if the -console option is active
- or by selecting Analyze from the File menu of Rocview.
On rerunning the analyzer after changes in the track plan all routes with an ID starting with “autogen-” that became invalid, e.g. due to changes in the relations of blocks or by introducing direction tracks, will be deleted from the route list.
Manually added routes not starting with “autogen-” will stay in the list unmodified.
Sensors have to be assigned to the routes on the routes tab found in the block properties. The sensors are assigned to the routes all and all-reverse, respectively. The all route is for all routes heading towards the + side of the block (marked with the little + in SpDrS60 theme). The all-reverse route accordingly in used for all routes heading towards the - side of the block.
Direction tracks (s. also Types of Tracks) can be used to restrict the routes generated by the analyser to one particular direction. For this purpose the direction track is placed between one or more blocks:
Connectors can be used to connect distant elements: The analyser is seeking for a counterpart (second connector) in the same direction and ignores gaps and elements between these two. Example: Connectors illustrating a bridge.
Until revision 4345:
- Corresponding connectors must be on the same track plan level and their orientation must be in the way shown in the above example: The connectors must face each other.
- The maximum distance between corresponding connectors is 9 grid elements.
Since revision 4346:
- The maximum distance between corresponding connectors is unlimited
- Connectors on the same track plan level where the orientation is in the way shown in the above example and the connectors face each other are handled as counterparts (Exception below)
Since revision 4346: Connectors configured with a track number between 10 and 99 must have a corresponding connector with the same track number anywhere in the plan. The direction of the counterpart doesn't matter. The counterpart may be on a different track plan level.
Connectors should not be used between modules.
<stlist> <st id="autogen-[01+]-[02+]" bka="01" bkb="02" bkaside="true" bkbside="true" show="false" x="0" y="0"> <swcmd id="sw1" cmd="straight"/> </st> <st id="autogen-[01+]-[03+]" bka="01" bkb="03" bkaside="true" bkbside="true" show="false" x="0" y="0"> <swcmd id="sw1" cmd="turnout"/> </st> <st id="autogen-[04+]-[01-]" bka="04" bkb="01" bkaside="true" bkbside="false" show="false" x="0" y="0"/> <st id="autogen-[02-]-[04-]" bka="02" bkb="04" bkaside="false" bkbside="false" show="false" x="0" y="0"> <swcmd id="sw2" cmd="straight"/> </st> <st id="autogen-[03-]-[04-]" bka="03" bkb="04" bkaside="false" bkbside="false" show="false" x="0" y="0"> <swcmd id="sw2" cmd="turnout"/> </st> </stlist>