block-gen-en
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
block-gen-en [2022/02/06 11:38] – [Allow change direction] besra | block-gen-en [2024/01/25 14:43] (current) – rjversluis | ||
---|---|---|---|
Line 2: | Line 2: | ||
[[: | [[: | ||
[[: | [[: | ||
- | * [[block-index-en|Index]] | **General** | [[: | + | * [[block-index-en|Index]] | **General** | [[: |
Line 28: | Line 28: | ||
In that case is also necessary, that the Block option __**[[# | In that case is also necessary, that the Block option __**[[# | ||
+ | >// | ||
\\ | \\ | ||
Line 66: | Line 67: | ||
\\ | \\ | ||
- | =====FiFo | + | =====FiFo===== |
This feature is only usable with automobiles which have infra red detectors to keep distance to the vehicles ahead.\\ | This feature is only usable with automobiles which have infra red detectors to keep distance to the vehicles ahead.\\ | ||
__In all other cases enabling this feature will lead to **accidents**.__\\ | __In all other cases enabling this feature will lead to **accidents**.__\\ | ||
- | \\ | + | ====Size==== |
The size is the number of allowed concurrently automobiles in this block.\\ | The size is the number of allowed concurrently automobiles in this block.\\ | ||
- | \\ | + | ====Gap==== |
In addition a gap can be specified here. This should be the gap the cars keep to each other due to their Infrared-Detectors.\\ | In addition a gap can be specified here. This should be the gap the cars keep to each other due to their Infrared-Detectors.\\ | ||
If this gap is >0 the length of the cars + the gap will be taken into account with regard to the block length. | If this gap is >0 the length of the cars + the gap will be taken into account with regard to the block length. | ||
Line 80: | Line 81: | ||
* In combination with the __**[[# | * In combination with the __**[[# | ||
* Is not compatible with the **enter2route** event. | * Is not compatible with the **enter2route** event. | ||
+ | |||
+ | > **Note on FiFo blocks for cars:** If the FiFo size is greater than 0 in a block, waiting is ignored, ... see also [[block-details-en# | ||
\\ | \\ | ||
Line 139: | Line 142: | ||
The block infrastructure is configured using the following flags: | The block infrastructure is configured using the following flags: | ||
- | ====Electrified==== | + | ====Electrified |
This option can be activated for blocks equipped with a catenary. \\ | This option can be activated for blocks equipped with a catenary. \\ | ||
- | If NOT set this prevents locos with **engine type electric** (see **[[: | + | If NOT set this prevents locos with **engine type electric** (see **[[: |
Line 222: | Line 225: | ||
>The function of BBT is defined for the driving distance between **enter** and **in**. | >The function of BBT is defined for the driving distance between **enter** and **in**. | ||
>Is there for the block only one feedback **enter2in**, | >Is there for the block only one feedback **enter2in**, | ||
+ | **Therefore it is strongly discouraged to use BBT __and__ enter2in sensors together in the same block**. | ||
>An **enter2in** defined sensor should be changed to **enter** and at the locomotives the option __**[[loc-bbt-en# | >An **enter2in** defined sensor should be changed to **enter** and at the locomotives the option __**[[loc-bbt-en# | ||
>In this case the **in** event is determined only by the BBT timing and does not collide with another timer. \\ | >In this case the **in** event is determined only by the BBT timing and does not collide with another timer. \\ | ||
Line 273: | Line 277: | ||
This option can only be used in case the enter detection is always free if the train is in the block.\\ | This option can only be used in case the enter detection is always free if the train is in the block.\\ | ||
A ghost will be reported if the enter detection is triggered in case there is already a train __in__ the block.\\ | A ghost will be reported if the enter detection is triggered in case there is already a train __in__ the block.\\ | ||
- | Look for __**[[: | + | Look for __**[[: |
\\ | \\ | ||
+ | ==== Check for free destinations until reaching IN ==== | ||
+ | Is only effective in this block for locomotives whose __**[[loc-details-en# | ||
+ | |||
+ | \\ | ||
+ | ==== Assign train ==== | ||
+ | If activated, a train in this block is automatically assigned to the incoming locomotive at the " | ||
+ | Disabled by default. \\ | ||
+ | ==== Timer events ==== | ||
+ | This option displays the remaining seconds for the locomotive to wait in this block in a corresponding "State signal" | ||
+ | Disabled by default. \\ | ||
+ | Consumes a lot of computing power in the Rocrail server and Rocrail clients. \\ | ||
+ | **Requirements: | ||
+ | - Rocrail Properties / Automatic / Event / Timer events = ON; (do not forget to restart Rocrail after having modified this value) \\ | ||
+ | - Block Properties / General / Configuration / Timer events = ON; \\ | ||
+ | - a "State signal" | ||
+ | - the locomotive must wait in this block; \\ | ||
+ | - (Rev. 2.1.3680+) \\ | ||
+ | |||
=====Actions===== | =====Actions===== |
block-gen-en.1644143880.txt.gz · Last modified: 2022/02/06 11:38 by besra