Innovative Model Railroad Control System

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
======LDT HSI-88 RS232======
[[:english#command_stations|{{  :interface.png}}]][[:english|{{  :rocrail-logo-35.png}}]]
[[english|Content]] -> [[english#command_stations|Command Stations]] ->   **LDT**
  * **[[:hsi88-en|HSI-88 RS232]]** | [[:inter10-en|INTER-10]]
   

// \\ // \\
|< >|
|  Check for alternatives like Tams Zeus. \\ //[[#tams_s88-bidib-link/zeus_in_hsi-mode| See note further down this page]]//  |
 \\

 \\
{{ hsi-88.jpg?200}}
=====Setup=====
{{:hsi88:hsi88-setup-en.png}}\\

 \\
=====Interface ID=====
Mostly the HSI-88 is used as a second interface for sensor reading only. Therefore it is necessary to set the **iid** attribute to link sensors in the plan xml file which is described in chapter [[multicontrollers-fr|Multiple Controllers]].
 \\
=====Device=====
The HSI-88 comes with a 9 pin serial cable, and is as far as known wired "1 to 1".
If your computer does not feature a serial device you can use an __**[[:usb-rs232-en|recommended USB to RS232 converter]]**__ which ist mostly mapped as "**/dev/ttyUSB0**" under Linux and as "**COM3**" or "**COM4**" under Windows.

 \\

=====S88 Chain=====
Number of **16-Port** modules connected on each chain. \\

**Note:**\\
The first address of the first module of each chain immediately follows the last address of the last defined module of the previous string. \\
This also applies if fewer modules are actually connected than are defined.
> ** Example: ** \\ If three modules are defined for the first/left chain, their last address is = 48 \\ For the second/middle chain, the first address = 49
 \\
{{  https://tams-online.de/WebRoot/Store11/Shops/642f1858-c39b-4b7d-af86-f6a1feaca0e4/MediaGallery/46_BiDiB/Uebersichten/ZEUS_FG_Zeichnung.png?300}}
===== Tams s88-BiDiB-Link/ZEUS in the HSI mode =====
  * Type: RS232
  * Baudrate: 9600
  * modules connected to "Bus 1" (middle connector on tams) have to be configured as "s88 chain left"
  * modules connected to "Bus 2" have to be configured as "s88 chain middle"
  * modules connected to "Bus 3" have to be configured as "s88 chain right"\\

The table shows the different assignment of the S88 chains from **HSI88 (LDT)** and **ZEUS (Tams)** to the settings in the dialog.
|< >|
^  HSI88 dialog  ^^^^ 
^  S88 Chain  ^  left  ^  middle  ^  right  ^
|  HSI88 (LDT)  |  LEFT  |  MIDDLE  |  RIGHT  |
|  ZEUS (Tams)  |  Bus 1 \\ middle  |  Bus 2 \\ left  |  Bus 3 \\ right  |

=====Options=====

====Delay====
If activated the sensor reports low first after the delay timing to avoid unwanted events cause by bad contact of wheels.\\
The delay timer will be set again to this value if it was high within this timing.\\
The max. is 2000ms which is also advised and used in other sensor reporting devices.\\
 

====CTS====
Option for DIY compatible devices to disable hardware handshake.\\

 \\

=====Links=====
  * Protocol: {{hsi88:hsi88_befehlssatz.pdf}}