loc-int-en
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
loc-int-en [2020/10/03 08:30] – [Step range] rjversluis | loc-int-en [2024/04/18 02:15] (current) – [Protocol] rainerk | ||
---|---|---|---|
Line 2: | Line 2: | ||
[[: | [[: | ||
[[: | [[: | ||
- | * [[: | + | * [[: |
Line 10: | Line 10: | ||
LocoDialog Interface Tab. | LocoDialog Interface Tab. | ||
- | {{: | + | {{: |
=====Interface ID===== | =====Interface ID===== | ||
- | Only set this to the IID you set in the rocrail.ini | + | If more than one command station is used, then the command station that is responsible for controlling the loc-decoder is specified in this field. The " |
- | \\ | + | |
====All==== | ====All==== | ||
If this option is activated all Loco and Function commands will send to all connected Command stations. | If this option is activated all Loco and Function commands will send to all connected Command stations. | ||
Line 41: | Line 41: | ||
If the __address is set to zero__ the protocol should be set to **Analog** for __**[[: | If the __address is set to zero__ the protocol should be set to **Analog** for __**[[: | ||
- | **Note:** // | + | **Notes:** \\ |
+ | //With Rev. 2.1.4466+ the term "Serverdefined" was replaced by " | ||
+ | Default, is the default mobile digital protocol used by the Command Station (CS). | ||
This setting is only of interest in case of multi protocol CS like Ecos/ | This setting is only of interest in case of multi protocol CS like Ecos/ | ||
For a "DCC only" CS this option has no effect at all. | For a "DCC only" CS this option has no effect at all. | ||
Line 108: | Line 110: | ||
\\ | \\ | ||
====Dir Change pause==== | ====Dir Change pause==== | ||
- | Some old Delta like decoders need some pause between a direction change and the last turnout command. With about 100ms this will do the trick when running DDX. | + | Some old Delta like decoders need some pause between a direction change and the last turnout command. With about 100ms this will do the trick. |
\\ | \\ | ||
====Poll info==== | ====Poll info==== | ||
Line 139: | Line 141: | ||
| 2 | Max. Step | | | | 2 | Max. Step | | | ||
| 3 | PWM width factor | Example for 100 speed steps: 1=10kHz, 10=1kHz, 100=100Hz, 1000=10Hz | | | 3 | PWM width factor | Example for 100 speed steps: 1=10kHz, 10=1kHz, 100=100Hz, 1000=10Hz | | ||
+ | |||
+ | ====Regulated==== | ||
+ | Uncheck this option __**only**__ if the decoder has accelerating and decelerating not implemented.\\ | ||
+ | The interval is the time between the speed steps.\\ | ||
+ | \\ | ||
+ | |||
=====Acceleration===== | =====Acceleration===== | ||
====Adjust acceleration==== | ====Adjust acceleration==== | ||
Line 146: | Line 154: | ||
* The new calculated acceleration value will be written by POM in CV3 after assigning a train or in case __**[[: | * The new calculated acceleration value will be written by POM in CV3 after assigning a train or in case __**[[: | ||
* The min. acceleration value will be written by POM in CV3 after releasing the assigned train. | * The min. acceleration value will be written by POM in CV3 after releasing the assigned train. | ||
+ | |||
+ | MFX Protocoll - start-up delay (tested with CS2): | ||
+ | * Decoder mSD/3 - version 3.2 : CV178 index 1 | ||
+ | * Decoder mSD - version 1.17.19 : CV78 index 1 | ||
+ | * Decoder mfx - version 0.0.24.186 : CV78 index 1 | ||
====Max. Load==== | ====Max. Load==== | ||
Line 166: | Line 179: | ||
\\ | \\ | ||
+ | |||
+ | |||
+ | |||
+ | \\ | ||
+ | =====Notes on none Regulated Decoders===== | ||
+ | **Deprecated**\\ | ||
+ | ====Interval==== | ||
+ | This option is not active and greyed out by default. It can be used for old-fashioned decoders offering no regulation and mass simulation. | ||
+ | * Regulated (see below) has to be deactivated in order to enable Interval. | ||
+ | |||
+ | The Interval merges in a pause between the decoder steps with a value of 1 corresponding to 100ms. With modern decoders this parameter is not needed and should be left to zero. \\ | ||
+ | |||
+ | > **Tip:** The Interval can be used to increase the deceleration / acceleration for decoders with a very limited tuning range. Some older Marklin locos with control potentiometers suffer from this limitation. Small interval values, e. g. in the range of 1 to 5, may help in this case. It should be noted that no other locos in need of automatic speed control at inclines (see **Regulated** below) are present on the layout and that in all blocks the type of incline should be set to " | ||
+ | |||
+ | ====Regulated==== | ||
+ | | SBT will be disabled in case this option is __not__ set. |\\ | ||
+ | If the decoder has motor management (BEMF) this flag should be set to prevent velocity changes by Rocrail when a locomotive enter a block defined as an incline block. \\ | ||
+ | Deactivating this option activates **Interval** (see above) and automatic speed control at inclines. \\ | ||
+ | |||
+ | > **Note:** Rocrail is able to adjust the speed at inclines within certain limits in auto mode. The type of incline has to be specified in the block properties. | ||
+ | |||
+ | The following table gives hints on the impact of the parameters. It is supposed that the **[[# | ||
+ | \\ | ||
+ | | ^Speed in steps and time \\ Interval = 5 (0,5 sec / step) \\ Speed at the beginning of the braking: 100 km/ | ||
+ | ^ steps ^ 1 ^ 2 ^ 3 ^ 4 ^ 5 ^ 6 ^ 7 ^ 8 ^ 9 ^ 10 ^ 11 ^ 12 ^ 13 ^ 14 ^ 15 ^ 16 ^ 17 ^ 18 ^ | ||
+ | ^ time / sec ^ 0,5 ^ 1,0 ^ 1,5 ^ 2,0 ^ 2,5 ^ 3,0 ^ 3,5 ^ 4,0 ^ 4,5 ^ 5,0 ^ 5,5 ^ 6,0 ^ 6,5 ^ 7,0 ^ 7,5 ^ 8,0 ^ 8,5 ^ 9,0 ^ | ||
+ | ^ Decelerate \\ 5 km/h | 95 | 90 | 85 | 80 | 75 | 70 | 65 | 60 | 55 | 50 | 45 | 40 | 35 | 30 | 25 | 20 | 15 | 10 | **km/ | ||
+ | ^ 10 km/h | 90 | 80 | 70 | 60 | 50 | 40 | 30 | 20 | 10 | **km/ | ||
+ | ^ 15 km/h | 85 | 70 | 55 | 40 | 25 | 10 | **km/ | ||
+ | ^ 20 km/h | 80 | 60 | 40 | 20 | 10 |**km/ | ||
+ | |||
+ | :!: Independently of the values in the table, the breaking will end at the speed defined in **V_Min**.\\ | ||
+ | \\ | ||
+ | **Hint:** At interval = **10** the number of steps = time in seconds. \\ | ||
+ | Higher values for **Interval** and/or **Decelerate** reduce the amount of necessary steps respectively speed commands.\\ | ||
+ | This can help to avoid the above mentionned overload of the command station. | ||
+ | |||
+ | **Example: | ||
+ | At Interval = 10 and Decelerate = 10 the reduction takes also place in 9 seconds, but with only 9 steps respectively commands.\\ | ||
+ | |||
+ | > **Hint:** The speed steps are not visible in the throttle, but only in the trace or on the real layout. |
loc-int-en.1601706600.txt.gz · Last modified: 2020/10/03 08:30 by rjversluis