loc-sbt-en
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
loc-sbt-en [2020/12/26 14:10] – [SBT] smitt48 | loc-sbt-en [2022/11/24 11:13] (current) – rjversluis | ||
---|---|---|---|
Line 2: | Line 2: | ||
[[: | [[: | ||
[[english|Content]] -> [[english# | [[english|Content]] -> [[english# | ||
- | * [[loc-index-en|Index]] | [[loc-gen-en|General]] | [[loc-int-en|Interface]] | [[: | + | * [[loc-index-en|Index]] | [[loc-gen-en|General]] | [[loc-int-en|Interface]] | [[: |
\\ | \\ | ||
=====SBT Tab===== | =====SBT Tab===== | ||
- | {{: | + | {{: |
The SBT records can be sorted by clicking on one of the columns headers.\\ | The SBT records can be sorted by clicking on one of the columns headers.\\ | ||
Line 25: | Line 25: | ||
This means that once switched on, SBT applies everywhere - for that loc. \\ | This means that once switched on, SBT applies everywhere - for that loc. \\ | ||
**[[# | **[[# | ||
- | **[[# | + | **[[# |
+ | |||
+ | * **Important: | ||
====Default override==== | ====Default override==== | ||
Where the default values of SBT do not fit, create an individual line with different values for the corresponding block. \\ | Where the default values of SBT do not fit, create an individual line with different values for the corresponding block. \\ | ||
Line 74: | Line 76: | ||
\\ | \\ | ||
- | =====None Regulated Decoders===== | ||
- | **Deprecated**\\ | ||
- | ====Interval==== | ||
- | This option is not active and greyed out by default. It can be used for old-fashioned decoders offering no regulation and mass simulation. | ||
- | * Regulated (see below) has to be deactivated in order to enable Interval. | ||
- | |||
- | The Interval merges in a pause between the decoder steps with a value of 1 corresponding to 100ms. With modern decoders this parameter is not needed and should be left to zero. \\ | ||
- | |||
- | > **Tip:** The Interval can be used to increase the deceleration / acceleration for decoders with a very limited tuning range. Some older Marklin locos with control potentiometers suffer from this limitation. Small interval values, e. g. in the range of 1 to 5, may help in this case. It should be noted that no other locos in need of automatic speed control at inclines (see **Regulated** below) are present on the layout and that in all blocks the type of incline should be set to " | ||
- | |||
- | ====Regulated==== | ||
- | | SBT will be disabled in case this option is __not__ set. |\\ | ||
- | If the decoder has motor management (BEMF) this flag should be set to prevent velocity changes by Rocrail when a locomotive enter a block defined as an incline block. \\ | ||
- | Deactivating this option activates **Interval** (see above) and automatic speed control at inclines. \\ | ||
- | |||
- | > **Note:** Rocrail is able to adjust the speed at inclines within certain limits in auto mode. The type of incline has to be specified in the block properties. | ||
- | |||
- | The following table gives hints on the impact of the parameters. It is supposed that the **[[# | ||
- | \\ | ||
- | | ^Speed in steps and time \\ Interval = 5 (0,5 sec / step) \\ Speed at the beginning of the braking: 100 km/ | ||
- | ^ steps ^ 1 ^ 2 ^ 3 ^ 4 ^ 5 ^ 6 ^ 7 ^ 8 ^ 9 ^ 10 ^ 11 ^ 12 ^ 13 ^ 14 ^ 15 ^ 16 ^ 17 ^ 18 ^ | ||
- | ^ time / sec ^ 0,5 ^ 1,0 ^ 1,5 ^ 2,0 ^ 2,5 ^ 3,0 ^ 3,5 ^ 4,0 ^ 4,5 ^ 5,0 ^ 5,5 ^ 6,0 ^ 6,5 ^ 7,0 ^ 7,5 ^ 8,0 ^ 8,5 ^ 9,0 ^ | ||
- | ^ Decelerate \\ 5 km/h | 95 | 90 | 85 | 80 | 75 | 70 | 65 | 60 | 55 | 50 | 45 | 40 | 35 | 30 | 25 | 20 | 15 | 10 | **km/ | ||
- | ^ 10 km/h | 90 | 80 | 70 | 60 | 50 | 40 | 30 | 20 | 10 | **km/ | ||
- | ^ 15 km/h | 85 | 70 | 55 | 40 | 25 | 10 | **km/ | ||
- | ^ 20 km/h | 80 | 60 | 40 | 20 | 10 |**km/ | ||
- | |||
- | :!: Independently of the values in the table, the breaking will end at the speed defined in **V_Min**.\\ | ||
- | \\ | ||
- | **Hint:** At interval = **10** the number of steps = time in seconds. \\ | ||
- | Higher values for **Interval** and/or **Decelerate** reduce the amount of necessary steps respectively speed commands.\\ | ||
- | This can help to avoid the above mentionned overload of the command station. | ||
- | |||
- | **Example: | ||
- | At Interval = 10 and Decelerate = 10 the reduction takes also place in 9 seconds, but with only 9 steps respectively commands.\\ | ||
- | > **Hint:** The speed steps are not visible in the throttle, but only in the trace or on the real layout. |
loc-sbt-en.1608988216.txt.gz · Last modified: 2020/12/26 14:10 by smitt48