User Tools

Site Tools


rocgui-gamepad-en

Rocview Gamepad Support

ContentRocview General



Deprecated


Rocview supports up to 4 connected gamepads for controlling locomotives.
The Gamepad support must be enabled.
In case a gamepad is connected, a locomotive can be selected with function 10 which pops up the selection dialog (see below).
With the D-pad a locomotive from the list can be selected which must be activated with the function 10 button.

Dialogue Mobile selection


Predefined action mapping

Button Action
1 to 4 decoder function 1 to 4
5 change direction
6 lights on/off
7 stop (not emergency)
8 track power off
9 track power on
10 select locomotive (dialog open/close)
D-pad speed up/down, or scroll through the loc list

These are the predefined button definitions.
The values are zero indexed. (mapping 0 is button 1)


How to map a GamePad

After the GamePad is connected and pressing the buttons and Axis you will get messages in the trace like these:

JsEvent dev=0, type=1, number=0, value=1, msec=50766908
JsEvent dev=0, type=1, number=1, value=1, msec=50773640
JsEvent dev=0, type=1, number=2, value=1, msec=50774584
JsEvent dev=0, type=1, number=3, value=1, msec=50775384
JsEvent dev=0, type=2, number=5, value=-32767, msec=50778792
JsEvent dev=0, type=2, number=5, value=0, msec=50779824

Type 1 is a Button, type 2 are axis.


Setup in Rocview

Possible entries:

  • V: button used for acceleration/decelleration
  • Repeat: auto repeat interval in case the acceleration button is kept pressed, entry is in in msec.
    • smaller numbers get higher repeat rate.
    • "0" means autorepeat = off
  • Direction: button to change loco direction, in case it is pressed loco will: decelerate , stop, accelerate in opposite direction
  • Stop: button to stop the loco
  • Decoder steps: defines how much decoder steps are accelerated/decelerated per keypress
  • Lights: button to toggle lights
  • F1-12: button to toggle F1-F12
    • -1 for not used
  • on/off: button to switch on/off command station power (not all command station may support this)


Trouble shooting

Try todo the following test running Linux:

  • open a console
  • connect the gamepad
  • type the command:
  cat /dev/input/js0
or
  cat /dev/js0
  • press all buttons one after another starting with button 1
  • press the D-Pad in all direction.

The console output should show something like this (depends on the console codepage settings):

The Gamepad is not useable if there is no output on pressing a button or D-Pad.

Now start the Rocview in a console:

./rocview -debug
  • insert the gamepad
  • touch all buttons and D-Pad direction as you did with the previouse test.

It is all a matter of mapping:

http://www.rocrail.net/doc/rocrail-wrappers/wrapper-en.html#jsmap

If your D-Pad generates different values like those ones: (rocview trace with debug lines)

20071219.173903.558 g9999D js-reade OJS      0110 handle=9, devnr=0, type=2, number=4, value=0, msec=27128764
20071219.173903.559 g9999I main     js       0162 JsEvent dev=0, type=2, number=4, value=0, msec=27128764
20071219.173903.640 g9999D js-reade OJS      0110 handle=9, devnr=0,type=2,number=3, value=0, msec=27128844
20071219.173903.641 g9999I main     js       0162 JsEvent dev=0, type=2, number=3, value=0, msec=27128844

Function button mapping: (rocview trace)

20071224.090542.371 g9999I js-reade Logitech 0069 JS 1(Logitech Logitech Dual Action) has 6 axes and 12 buttons. Driver version is 2.1.0.
20071224.090543.529 g9999I main     js       0162 JsEvent dev=0, type=1, number=0, value=1, msec=3162540
20071224.090543.720 g9999I main     js       0162 JsEvent dev=0, type=1, number=0, value=0, msec=3162724
20071224.090553.122 g9999I main     js       0162 JsEvent dev=0, type=1, number=1, value=1, msec=3172132
20071224.090553.313 g9999I main     js       0162 JsEvent dev=0, type=1, number=1, value=0, msec=3172316
20071224.090556.663 g9999I main     js       0162 JsEvent dev=0, type=1, number=2, value=1, msec=3175668
20071224.090556.824 g9999I main     js       0162 JsEvent dev=0, type=1, number=2, value=0, msec=3175828
20071224.090557.689 g9999I main     js       0162 JsEvent dev=0, type=1, number=3, value=1, msec=3176692
20071224.090557.852 g9999I main     js       0162 JsEvent dev=0, type=1, number=3, value=0, msec=3176860

The number corresponds to the number of the gamepad button subtracted with 1. In this example the button 1 to 4 where pressed and meets the default values in the jsmap.

Adjust the jsmap in the rocgui.ini to meet your gamepad. Example:

<jsmap step="1" updown="5" repeat="500" reverse="4" stop="6" light="5" f1="0" f2="1" f3="2" f4="3" poweron="8" poweroff="7"/>
rocgui-gamepad-en.txt · Last modified: 2022/02/02 11:24 by besra