User Tools

Site Tools


can-gca2g-en

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
can-gca2g-en [2018/11/12 08:56] – external edit 127.0.0.1can-gca2g-en [2020/07/02 18:55] (current) rjversluis
Line 17: Line 17:
  \\  \\
 The CAN-GC2G is an alternative to the CAN-GC2 with integrated drivers, useable as a complet unit without \\ The CAN-GC2G is an alternative to the CAN-GC2 with integrated drivers, useable as a complet unit without \\
-extra drivers, running on the mergCBUS open source CAN standard. \\+extra drivers, running on the CANBUS open source CAN standard. \\
 This unit enables direct connection of the following peropheral:  This unit enables direct connection of the following peropheral: 
   * 2 x Turnout output for single coil units.   * 2 x Turnout output for single coil units.
Line 33: Line 33:
 |   {{:can-gc2g_pict_03.jpg?400}}   | |   {{:can-gc2g_pict_03.jpg?400}}   |
  
-A jumper makes it possible to set terminator on the last board in the mergCBUS chain.\\+A jumper makes it possible to set terminator on the last board in the CANBUS chain.\\
 This jumper connects a 120 Ohm resistor to the Merg CBUS.\\ This jumper connects a 120 Ohm resistor to the Merg CBUS.\\
 The base for creation this board is to make use of CBUS easier for garden railroad.\\ The base for creation this board is to make use of CBUS easier for garden railroad.\\
Line 41: Line 41:
 and addionally there is place and control for two relays with 10Amp contacts to be able to reverse the rail power inside a reverse loop.\\ and addionally there is place and control for two relays with 10Amp contacts to be able to reverse the rail power inside a reverse loop.\\
 These relays will be controlled by Rocrail, direct control via reed contact or Hall sensor is also optional.\\ These relays will be controlled by Rocrail, direct control via reed contact or Hall sensor is also optional.\\
-Power, as available in Merg CBUS-cable, is only used for supply of mergCBUS board itself.\\+Power, as available in Merg CBUS-cable, is only used for supply of CANBUS board itself.\\
 The reverse loop relays and the outputs for turnout need 24 V by standard.\\ The reverse loop relays and the outputs for turnout need 24 V by standard.\\
 Adaption to lower voltage needs different 10Amp relays.\\ Adaption to lower voltage needs different 10Amp relays.\\
Line 81: Line 81:
 and do not have to worry about correct polarisation by entering or leaving the reverse loop.\\ and do not have to worry about correct polarisation by entering or leaving the reverse loop.\\
 These feature needs different firmware for IC3.\\ These feature needs different firmware for IC3.\\
-If you are intersted in that option, ask {{peter.giling@rocrail.net|Peter}}.\\+If you are intersted in that option, ask [[peter.giling@rocrail.net|Peter]].\\
  
  
Line 197: Line 197:
  
 ====Save output state==== ====Save output state====
-Write the output state in EEPROM after detecting a **power off command** on the mergCBUS.\\+Write the output state in EEPROM after detecting a **power off command** on the CANBUS.\\
 The outputs will be restored after the [[:can-gca2G-en|CAN-GC2G]] is powered on.\\ The outputs will be restored after the [[:can-gca2G-en|CAN-GC2G]] is powered on.\\
  
Line 222: Line 222:
 | **BK** | Block | Input with a 2 seconds delayed off. (±50ms) | Occupancy detectors. | | **BK** | Block | Input with a 2 seconds delayed off. (±50ms) | Occupancy detectors. |
 | **SW** | Switch | Continuous output. | Single coil switch drivers like servos. | | **SW** | Switch | Continuous output. | Single coil switch drivers like servos. |
-| **PU** | Pulse | Output with x ms activation time. (±50ms) | Note: A [[:switch-int-en#switch_time|software timed off]] is not possible with mergCBUS; It is realized in the hardware. | \\+| **PU** | Pulse | Output with x ms activation time. (±50ms) | Note: A [[:switch-int-en#switch_time|software timed off]] is not possible with CANBUS; It is realized in the hardware. | \\
  
 ====Pulse time==== ====Pulse time====
can-gca2g-en.txt · Last modified: 2020/07/02 18:55 by rjversluis