dr5000-en
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
dr5000-en [2020/05/31 07:55] – [Z21] rjversluis | dr5000-en [2024/03/16 11:12] (current) – [Z21] rjversluis | ||
---|---|---|---|
Line 7: | Line 7: | ||
{{: | {{: | ||
\\ | \\ | ||
- | |< >| | ||
- | | **Use always the USB port in case of DR5000 configuration.** | | ||
- | =====Setup | + | =====Setup |
- | {{: | + | |
- | \\ | + | |
- | ====Devices===== | + | |
- | Following serial devices are added for the DR5000: | + | |
- | ^ Windows ^ Linux & RaspBerry Pi ^ Mac OS X ^ Protocol ^ Library ^ Sub-Library / Type ^ Baudrate ^ | + | |
- | | COM4 | / | + | |
- | | COM6 | / | + | |
- | | COM5 | / | + | |
- | + | ||
- | **After successful configuration, | + | |
- | \\ | + | |
- | ====Setup USB LocoNet Rocrail==== | + | |
- | {{: | + | |
- | {{: | + | |
- | More details are described below. \\ | + | |
- | + | ||
- | + | ||
- | ====Setup LAN==== | + | |
LocoNet, LNTCP, is recommended for the DR5000 communication. (Xpressnet seems to be too slow and is missing some events.)\\ | LocoNet, LNTCP, is recommended for the DR5000 communication. (Xpressnet seems to be too slow and is missing some events.)\\ | ||
====LocoNet LAN==== | ====LocoNet LAN==== | ||
Line 50: | Line 30: | ||
(Error message: Trace timer timed out for OPCODE 0xB0, to fix: increase timer)\\ | (Error message: Trace timer timed out for OPCODE 0xB0, to fix: increase timer)\\ | ||
- the time between switching on the system and starting Rocrail is too short, the DR 5000 should be left for a few moments until everything is ready for operation. \\ | - the time between switching on the system and starting Rocrail is too short, the DR 5000 should be left for a few moments until everything is ready for operation. \\ | ||
- | ===Options=== | ||
- | Some LocoNet Throttles do not set an ID and therefore the Speed will not be updated in the Rocrail clients. (Rocview, andRoc, Rocweb...)\\ | ||
- | See: __**[[: | ||
\\ | \\ | ||
+ | ====Loconet Options==== | ||
+ | {{: | ||
+ | \\ | ||
+ | |||
+ | Select " | ||
+ | |||
+ | Some LocoNet Throttles do not set an ID and therefore the Speed will not be updated in the Rocrail clients. (Rocview, andRoc, Rocweb…) | ||
+ | See: Zero Throttle ID for more information about this issue __**[[: | ||
+ | |||
+ | \\ | ||
====LocoNet Details==== | ====LocoNet Details==== | ||
- | {{:loconet: | + | {{:dr5000:dr5000-loconet-details-en.png?500}}\\ |
===Wait for slot data=== | ===Wait for slot data=== | ||
This number should be increased, max. 128, if the following error occurs: | This number should be increased, max. 128, if the following error occurs: | ||
Line 65: | Line 52: | ||
Default Rocrail will read up to 16 packets until it give up waiting for a free slot.\\ | Default Rocrail will read up to 16 packets until it give up waiting for a free slot.\\ | ||
This figure, the default of 16, seems to be too low for the DR5000.\\ | This figure, the default of 16, seems to be too low for the DR5000.\\ | ||
+ | |||
+ | ===Other Options=== | ||
+ | |< >| | ||
+ | ^ Option ^ Recommended Value ^ | ||
+ | | Switch time | 50ms | | ||
+ | | Slot ping | Off | | ||
+ | | Fast clock | Off | | ||
\\ | \\ | ||
====Z21==== | ====Z21==== | ||
- | See for Z21 settings __**[[: | + | See for Z21 library |
+ | |||
+ | **Note:** //Power, voltage and temp. are not reported; No measurement hardware available.// | ||
===DR5088RC=== | ===DR5088RC=== | ||
If using the Z21 protocol in combination with DR5088RC there is a shift in reported feedback and block(RailCom) addressing.\\ | If using the Z21 protocol in combination with DR5088RC there is a shift in reported feedback and block(RailCom) addressing.\\ | ||
Line 76: | Line 72: | ||
+ | \\ | ||
+ | =====Setup USB===== | ||
+ | {{: | ||
\\ | \\ | ||
+ | ====Devices===== | ||
+ | Following serial devices are added for the DR5000: | ||
+ | ^ Windows ^ Linux & RaspBerry Pi ^ Mac OS X ^ Protocol ^ Library ^ Sub-Library / Type ^ Baudrate ^ | ||
+ | | COM4 | / | ||
+ | | COM6 | / | ||
+ | Users who want to use the interface must be added to the '' | ||
+ | \\ | ||
+ | **After successful configuration, | ||
+ | \\ | ||
+ | ====Setup USB LocoNet Rocrail==== | ||
+ | {{: | ||
+ | {{: | ||
+ | More details are described below. \\ | ||
- | ====DrCmd==== | ||
- | {{ : | ||
- | 12.740+\\ | ||
- | The **drcmd** library has only limited support because the protocol is not documented.\\ | ||
- | ===Supported commands: | ||
- | * Power ON/OFF | ||
- | * Switch (FADA only) | ||
- | * Loco speed, direction and F0-F28 | ||
- | * Programming Track | ||
- | * POM | ||
- | ===Supported events:=== | ||
- | * S88 reporting | ||
- | * Switch reporting | ||
- | * Power events | ||
- | * Current and temperature | ||
- | * Loco speed, direction and F0 reporting | ||
- | \\ | ||
- | |||
- | ====Xpressnet LAN==== | ||
- | * __**[[: | ||
\\ | \\ | ||
=====Addressing===== | =====Addressing===== | ||
+ | ====Sensors==== | ||
+ | **Tip:** Use the [[: | ||
+ | |||
====Accessory==== | ====Accessory==== | ||
//Switches, Outputs and Signals.// | //Switches, Outputs and Signals.// |
dr5000-en.1590904554.txt.gz · Last modified: 2020/05/31 07:55 by rjversluis