# GCA08 High efficiency universal power supply for 1 or 3 Amp

## Description

On many places under the railraod table, we need all kind of DC power supplies.

Bying adapters is one option, nowadays also many of them are high effiency, meaning not evaporating a lot of energy into heat.

Unfortunately many of these adaptors do not give what they promise.

Furthermore, the very annoying thing about having these adaptors under your table is the fact that you also need 230V there.

And exactly that, specially where infants like to help there parents with this nice hobby, is not much to encourage.

The better option is to run a low 16V ac line under the table and use that.

This power supply will give you that option and can be set-up in various ways and voltages, either adjustable or solid.

For ac input, it needs at least the same voltage as the desired output.

If you are running dc line under the table, it should be at least 2 Volts higher than output.

Adjustable versions could be as low as 1,25 V, up to the maximum you put in.

The switching regulator is very energy efficient.

In everage the effiency will be more than 80%.

There are two units available:

- GCA08-1 1 Amp ouput, size 40×22 mm
- GCA08-3 3 Amp output, size 40×62 mm

## The final results

## GCA08-1, 1 Amp output

This simple supply can be used in different ways.

If you install a standard LM78xx regulator, it can supply a full 1 Amp when the regulator is cooled sufficiently.

Without cooling, it is very depending on the incoming voltage and the used current, how far you can.

If it goes too far (regulatir gets too hot) the regulator will stop.

Output voltage can be like 3,3 / 5 / 6 / 9 / 10 /12 / 15 / 18 / 24.

This is the cheapest way.

If you use a Traco-Power TSR 1-xxxx regulator, no cooling is need, and the full 1 Amp can be used.\\

No external settings are needed, since this very efficient chip is available in most common fixed voltages.

The maximum output is 1 Amp, input from transformer can be up to 20V ac or 24V dc.

A total of 6 parts are located on this board.

Efficiency with Teaco_Power chip is better than 90% which makes cooling totally unneeded.

## GCA08-3, 3 Amp output adjustable

This board is able to supply 3 Amp in a chosen voltage.

Please refer to tables below for selction of the right output.

## Hardware

GCA08-1 schematics |

GCA08-1 partslist |

GCA08-3 schematics |

GCA08-3 The parts list for adjustable 3 amp version |

N.B. Only complete ordered kits will be supported! |
---|

## Selecting the output.

This board can be equipped in 1 Amp outpur max, or 3 Amp, depening on the chosen chip.

Maximum input ratings for all configurations:

dc 30 Volt

ac 24 Volt

For correct calculation of needed transformer, see which tranformer below

Selection table for various voltages and current. |
---|

Outout (V) | VR1 for 1 Amp | VR1 for 3 Amp | R1 | R2 | P1 |
---|---|---|---|---|---|

1,24 | LM2575T-adj | LM2576T-adj | x | short* | no |

3,3 | LM2575T-3,3 | LM2576T-3,3 | x | short* | no |

5 | LM2575T-5 | LM2576T-5 | x | short* | no |

12 | LM2575T-12 | LM2576T-12 | x | short* | no |

** * *short means to insert a short bridge (piece of wire).
**

Other voltages can be achieved by installing resistor R1 and a small adjust potmeter 20K. |
---|

Outout (V) | VR1 for 1 Amp | VR1 for 3 Amp | R1 | R2 | P1 |
---|---|---|---|---|---|

1,24-12 V | LM2575T-adj | LM2576T-adj | 1 KΩ | no | 20 KΩ |

With this setup output will be adjustable from 1,24 V to max 26 V depending on input voltage.

Using a potmeter inserts the risk of output changing after a while.

Pometers are never stable on the long run.

This table shows various , not adjustable voltages. | |||||
---|---|---|---|---|---|

Vout (V) | VR1 for 1 Amp | VR1 for 3 Amp | R1 | R2 | P1 |

6 | LM2575T-adj | LM2576T-adj | 1 kΩ | 3,9 kΩ* | no |

8 | LM2575T-3,3 | LM2576T-3,3 | 1 kΩ | 5,6 kΩ | no |

9 | LM2575T-3,3 | LM2576T-3,3 | 1,8 kΩ | 12 kΩ | no |

10 | LM2575T-5 | LM2576T-5 | 1,2 kΩ | 8,6 kΩ | no |

16 | LM2575T-12 | LM2576T-12 | 1 kΩ | 12 kΩ | no |

Vales in this table are a close approach.

Far more exact values can be achieved by using 1% metal resistor from 96 series.

Resistors are calculated by the following formula.

R2 = R1 x ( ( Vout/1,24) -1) Ω |
---|

N.B. Potmeter is not installed. |

## Fuse F1

**ALWAYS INSTALL FUSE !!!!!!!!!!!**

Do not think it will be unnessacery, because little mistakes can couse insuries or fire hazard.

With PTC fuse assembled, you are always safe, and never have to worry about ever having to replace it.

Also the fuse need to be adapted to the the desired output.

In general the values for the multifuse sshould be:

For 1 Amp out use 0,5 - 0,8 Amp fuse.

For 3 Amp out use 1,5 - 1,85 Amp fuse.

## Which transformer ?

Basicly the transformer should have the following parameters:

Secundary voltage : minimal equal to output.

Power (in VA) Minimal (V x A x 1.2), where :

- V = Volt output

- A = Ampere output.

It is possible to use a DC power supply.

The input voltage should be at least 3V higher than output.

Trace: » gca08-en