loc-int-en
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
loc-int-en [2019/09/13 18:33] – [Placing] rjversluis | loc-int-en [2019/12/10 16:17] – rainerk | ||
---|---|---|---|
Line 28: | Line 28: | ||
*Marklin mfx-Decoders may need special settings depending on the command station. See the wiki page of the relevant command station, if applicable. | *Marklin mfx-Decoders may need special settings depending on the command station. See the wiki page of the relevant command station, if applicable. | ||
*Locos with address 0 (zero) are considered to be analog locos without decoders which are only supported by TrackDriver systems. " | *Locos with address 0 (zero) are considered to be analog locos without decoders which are only supported by TrackDriver systems. " | ||
- | The optional | + | ====Secondary Address==== |
+ | The optional | ||
====OID==== | ====OID==== | ||
Some Command Station, like the ESU Ecos, are using an Object ID instead of an address for referring to a specific loco.\\ | Some Command Station, like the ESU Ecos, are using an Object ID instead of an address for referring to a specific loco.\\ | ||
Line 38: | Line 39: | ||
Some command stations do support multiple protocols; Check the user manual for details.\\ | Some command stations do support multiple protocols; Check the user manual for details.\\ | ||
If the __address is set to zero__ the protocol should be set to **Analog** for __**[[: | If the __address is set to zero__ the protocol should be set to **Analog** for __**[[: | ||
- | \\ | + | |
+ | **Note:** // | ||
+ | This setting is only of interest in case of multi protocol CS like Ecos/ | ||
+ | For a "DCC only" CS this option has no effect at all. | ||
+ | Or for the Märklin 6051 its always Motorola. // | ||
+ | |||
=====Protocol version===== | =====Protocol version===== | ||
Line 73: | Line 79: | ||
This can be done with the [[https:// | This can be done with the [[https:// | ||
The port must be set to 5152.\\ | The port must be set to 5152.\\ | ||
+ | **Note:** //It can take up to 30 seconds before the first frames are coming in after starting the camera.//\\ | ||
{{: | {{: | ||
+ | |||
====Demo & Links==== | ====Demo & Links==== | ||
* Demo: https:// | * Demo: https:// | ||
Line 84: | Line 92: | ||
=====Options===== | =====Options===== | ||
====Mass==== | ====Mass==== | ||
- | Only to be used when this is an analog loco in combination of the Dinamo CS. (Check the documentation.) | + | Can be used: |
+ | * When this is an analog loco in combination of the Dinamo CS. (Check the documentation.) | ||
+ | * A WIO with the mobile option activated. | ||
+ | * A RocNetNode mobile decoder | ||
A value of 5 is a good start to experiment with. | A value of 5 is a good start to experiment with. | ||
\\ | \\ | ||
Line 95: | Line 106: | ||
:!: Use with care. This option is __not recommended__ and __not supported in the Forum__, and uses unnecessary CPU resources. :!: | :!: Use with care. This option is __not recommended__ and __not supported in the Forum__, and uses unnecessary CPU resources. :!: | ||
\\ | \\ | ||
+ | ====Invert==== | ||
+ | Inverts the hardware running direction.\\ | ||
+ | This is an alternative to program the direction in the decoder by CV29.\\ | ||
+ | < | ||
====Placing==== | ====Placing==== | ||
//Placing is the __logical__ forward direction.// | //Placing is the __logical__ forward direction.// | ||
- | When the loco runs the wrong direction this flag can be swapped.\\ | + | When the loco runs the wrong direction this flag can be swapped. This flag is not fixed and can change during automatic runs.\\ |
For commuters this flag is automatically swapped in __**[[: | For commuters this flag is automatically swapped in __**[[: | ||
This flag is default set and means a Loco run direction like coming out of the box; some older decoders do only remember the direction for a short period after shut-down the power.\\ | This flag is default set and means a Loco run direction like coming out of the box; some older decoders do only remember the direction for a short period after shut-down the power.\\ | ||
Line 103: | Line 118: | ||
If the flag is __not__ set the placing type is swapped.\\ | If the flag is __not__ set the placing type is swapped.\\ | ||
+ | Read also: **[[: | ||
+ | --></ | ||
====Polarisation==== | ====Polarisation==== | ||
A flag for correcting the BiDi, RailCom, direction in case the decoders is not correctly polarised. \\ | A flag for correcting the BiDi, RailCom, direction in case the decoders is not correctly polarised. \\ | ||
See also: __**[[: | See also: __**[[: | ||
- | |||
- | |||
- | |||
\\ | \\ | ||
+ | ====Step range==== | ||
+ | If __**[[arduino: | ||
=====Acceleration===== | =====Acceleration===== | ||
====Adjust acceleration==== | ====Adjust acceleration==== |
loc-int-en.txt · Last modified: 2024/04/18 02:15 by rainerk