Differences

This shows you the differences between two versions of the page.

--- mbus:cs3-en [2020/10/09 16:16] – rjversluis
+++ mbus:cs3-en [2022/05/01 10:40] (current) – [Switch/Output] rjversluis
@@ Line 2: / Line 2: @@
 [[:english#command_stations|{{  :interface.png}}]][[:english|{{  :rocrail-logo-35.png}}]]
 [[:english|Content]] -> **[[:english#command_stations|Command Stations]]** -> Märklin
-  * **[[:mbus:mbus-en|MBUS]]**
+  * **[[:mbus:mbus2-en|MBUS]]**
     * [[:mbus:functions-en|Function Codes]] | **[[:mbus:cs3-en|CS2/CS3]]** |  [[:mbus:mbus-en|TrackBox(GleisBox)]] | [[:mbus:channels-en|Channels]]
 {{:mbus:cs3plus.png?200}}\\
+^  The MCS2 library is replaced by the MBus library.  ^
 =====TCP Communication=====
@@ Line 14: / Line 16: @@
 ====Communication Type====
 The preferred way to communicate with the CS3 is by using the TCP type.\\
+The CS3 TCP port is factory set to 15731, the second port is not utilized.\\
+Classic CS2 UDP communication uses two port numbers, sending (Tx) and receiving (Rx). \\
+If the port entry is set to zero, it is automatically replaced with the default values, 15731 and 15730. \\
 {{:mbus:mbus-interface-en.png}}\\
-The CS3 TCP port is factory set to 15731.\\
 ====Overview====
 If all went well, the CS3 is listed in the CBUS/MBUS dialog:\\
@@ Line 40: / Line 45: @@
  \\
 ====LinkS88====
-|  //Starting with revision 15.073, this setup is no longer needed; Its detected automatically.//  |\\
+|  //This setup is no longer needed; Its detected automatically.//  |\\
-This setup is needed to be able to detect the sensor state at start up.\\
+<del>This setup is needed to be able to detect the sensor state at start up.</del>
 |{{:mbus:links88-setup-de.png?0x240}}|{{:mbus:mbus-sensors-en.png?0x240}}|\\
 An entry in the list is needed for each connected LinkS88 device.\\
@@ Line 55: / Line 60: @@
 Turn this option off in all other cases.\\
+====Auto switch delay====
+A switch delay time is always send in case this option is active. (Default active)\\
+This is independent of the individual [[:switch-int-en#switch_time|Switch Time]]. The global switch delay is used if the individual switch time is set to zero.\\
  \\
 =====Switch time=====
-__**[[:switch-int-en#switch_time|Activate this timer in case the used motor does not switch itself off!]]**__ \\
+__**[[:switch-int-en#switch_time|Activate this timer in case the motor does not switch itself off!]]**__ \\
 :!: Disabled end contacts will burn the coils of the motor if the switch time is not activated.\\
@@ Line 64: / Line 73: @@
 =====Addressing=====
 ====Switch/Output====
-An example for the real switch address **11**:
+An example for the real switch address **12**:
 |< >|
-^ Type ^ Address ^ Port ^ Calculation ^ Remark ^
+^ Type ^ Address ^ Port ^ Remark ^
-^ MADA |   3 |   4 |  (3-1)*4+(4-1)=11 | |
+^ MADA |   3 |   4 | Not supported! |
-^ PADA |   0 |  12 |  12-1=11 | Recommended: Same scheme as the display address in the CS2/CS3 GUI. |
+^ PADA |   0 |  12 | Same scheme as the display address in the CS2/CS3 GUI. |
-^ FADA |   - |  - | Not supported! | |
+^ FADA |   - |   - | Not supported! |
  \\
@@ Line 94: / Line 103: @@
  \\