Differences

This shows you the differences between two versions of the page.

--- mbus:mbus-en [2019/02/14 13:11] – [Dummy] rjversluis
+++ mbus:mbus-en [2019/02/19 18:04] – rjversluis
@@ Line 2: / Line 2: @@
 [[:english#command_stations|{{  :interface.png}}]][[:english|{{  :rocrail-logo-35.png}}]]
 [[:english|Content]] -> [[:english#command_stations|Command Stations]] -> **[[:english#can|CAN]]**
-  * [[:mbus:functions-en|Function Codes]]
+  * **[[:mbus:mbus-en|MBUS]]**
+    * [[:mbus:functions-en|Function Codes]] | [[:mbus:cs3-en|CS3]] | [[:mbus:channels-en|Channels]]
  \\
  \\
@@ Line 23: / Line 24: @@
  \\
+=====Setup=====
 {{mbus:mbus-setup-en.png}}\\
-=====Type=====
+====Type====
 This defines over which interface Rocrail communicate with CAN.\\
-====USB GridConnect====
+===USB GridConnect===
 //"For small systems."//\\
 The company [[https://www.gridconnect.com|Grid Connect]] defined an ASCII framing protocol designed for using frames over serial connections.\\
-The USB connection of the __**[[:arduino:rcan-en|CANGC2a]]**__ can be used for this type. (Baud rate fixed at 500000)\\
+The USB connection of the __**[[:arduino:rcan-en|CANGC2a]]**__ can be used for this type.\\
-====SocketCAN====
+Fixed baud rate of 500000.\\
+===SocketCAN===
 //"Highly recommended."//\\
 SocketCAN can be used in combination of the following components:
@@ Line 37: / Line 40: @@
   * __**[[:rocnet:pi01can-en|Pi01CAN]]**__, __**[[:cbus:socketcan-en|RPI-CAN]]**__
 The advantage of this type is the direct Rocrail Server connection with CAN; It can run without EtherNet and USB.\\
-The WiFi on the **Raspberry Pi 3 b+** can be used for visualisation by Rocview, Rocweb and/or andRoc.\\
+The WiFi on the **Raspberry Pi 3 B+** can be used for visualisation by Rocview, Rocweb and/or andRoc.\\
-====CC-Schnitte====
+===CC-Schnitte===
 //"If you already have one."//\\
 __**[[:cc-schnitte-en|CAN-Digital-Bahn]]**__ serial CAN interface.\\
 The communication does not use serial framing which could lead to wrong interpretations of data.\\
+Fixed baud rate of 500000.\\
-====TCP====
+===TCP===
-//"Alternative Märklin way."//\\
+//"The Märklin way."//\\
 Default port 15731.\\
 Compatible with CS2/CS3 communication.\\
-====UDP====
+===UDP===
-//"The Märklin way."//\\
+//"The old Märklin way."//\\
 Fixed read/write ports 15730/15731.\\
 Compatible with CS2/CS3 communication.\\
 The __**[[:mbus:canservice-en|CANService]]**__ application can also be used for UDP communication. This utility is automatically installed on Linux platform under /opt/rocrail/canservice.\\
-====Dummy====
+===Dummy===
 //"Just for testing without any hardware connected."//\\
 All CAN frames are echoed with the response bit set.\\
-==== Lawicel/SLCAN====
+=== LAWICEL / SLCAN ===
-The Lawicel/SLCAN protocol to use with common serial CAN interfaces like **[[http://www.fischl.de/usbtin/|USBTin]]**.\\
+The [[http://www.can232.com|LAWICEL]] / SLCAN protocol to use with common serial CAN interfaces like **[[http://www.fischl.de/usbtin/|USBTin]]**.\\
+Fixed baud rate of 115200.\\
  \\
-=====Hostname=====
+====Hostname====
 For UDP and TCP type.\\
 The extra field on the right is to set the TCP port; 15731 is used if not set.\\
  \\
-=====Device=====
+====Device====
 The serial device used with type **USB GridConnect** or **CC-Schnitte**.\\
  \\
-=====Protocol=====
+====Track Protocols====
 The supported digital protocols by the TrackBox.\\
 If all protocols are disabled in the settings, they will be all activated at startup. At least one protocol must be activated.\\
-=====Report state=====
+====Report state====
 Report the current, voltage and temperature of the **[[#channels|TrackBox channels]]**.
 |< >|
@@ Line 81: / Line 86: @@
  \\
-=====Options=====
+====Options====
-====Slot purge time====
+===Slot purge time===
 If a locomotive is nonactive for this period of time, and the speed is zero, it will be removed from the refresh cycle to make place for other locomotives.\\
 Purging is deactivated if this time is set to zero.\\
@@ Line 88: / Line 93: @@
-====Acknowledge sensor events====
+===Acknowledge sensor events===
 Acknowledge the Block type inputs of the __**[[:arduino:rcan-en|GC2a]]**__.\\
 Only the ON will be acknowledged. If an acknowledgement was not received the GC2a will resend the event until the block input goes OFF.\\
 The GC2a enables this option automatically after receiving the first acknowledge, and this will be active only for the current session.\\
-====Master====
+===Master===
 Puts the connected MS2 in slave mode and provide loco information.\\
 After the MS2 is in slave mode, a loco can be selected from the Rocrail server with the following sequence:\\
@@ Line 102: / Line 107: @@
 |  {{:mbus:ms-slave-select-en.jpeg}}  |\\
-====Read only====
+===Read only===
 Trace only the traffic on the CAN bus, and do not evaluate.\\
-====MSApp====
+===MSApp===
 {{ :mbus:msapp-disney.png?100}}{{ :mbus:msapp-icon.png}}
 Support for the [[https://www.maerklin.de/de/service/kundenservice/mainmobile-station-app-hilfe/|Mobile Station App]].\\
@@ Line 112: / Line 117: @@
  \\
-=====Programming track=====
+====Programming track====
 This output addressing can be used for activating a relay before programming.\\
 The TrackBox does not provide a separate output for programming. To avoid programming all locomotives on the main track, it can be helpful to switch to the isolated programming track.\\
@@ Line 156: / Line 161: @@
  \\
-=====TrackBox=====
-====Channels====
-Table of known channels:
-|< >|
-^ Channel ^ Measurement ^ Units ^
-|  1  | Current | mA |
-|  3  | Voltage | hundredth of V |
-|  4  | Temperature | C° |
-Those three channels will be polled every 5 seconds, and in case of a **[[#report_state|change reported]]** to the Rocrail Server.\\
-The Trackbox can be added to the __**[[:powerman-en|Power Manger]]**__ with address 1 or the UID.\\