mbus:mbus-en
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
mbus:mbus-en [2019/06/14 07:50] – [Options] rjversluis | mbus:mbus-en [2020/04/18 16:21] – [Tips] phg | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== MBUS ====== | + | ====== MBUS TrackBox====== |
[[: | [[: | ||
- | [[: | + | [[: |
* **[[: | * **[[: | ||
- | * [[: | + | * [[: |
- | \\ | + | |
- | | ToDo: UPDATE. | + | |
\\ | \\ | ||
=====Introduction===== | =====Introduction===== | ||
Line 12: | Line 10: | ||
The Command Station, Märklin TrackBox(GleisBox), | The Command Station, Märklin TrackBox(GleisBox), | ||
- | ====Overview==== | ||
- | {{mbus: | ||
====Devices==== | ====Devices==== | ||
- | {{ : | + | {{ : |
* Raspberry Pi + Rocrail Server + __**[[: | * Raspberry Pi + Rocrail Server + __**[[: | ||
* or Banana Pi M1 + Rocrail Server + [[http:// | * or Banana Pi M1 + Rocrail Server + [[http:// | ||
- | * __**[[: | ||
* Märklin TrackBox(GleisBox) [[https:// | * Märklin TrackBox(GleisBox) [[https:// | ||
* Märklin Mobile Station [[https:// | * Märklin Mobile Station [[https:// | ||
Line 32: | Line 27: | ||
//"For small systems."// | //"For small systems."// | ||
The company [[https:// | The company [[https:// | ||
- | The USB connection of the __**[[: | ||
Fixed baud rate of 500000.\\ | Fixed baud rate of 500000.\\ | ||
===SocketCAN=== | ===SocketCAN=== | ||
Line 39: | Line 33: | ||
* Raspberry Pi 2 or 3, __**[[: | * Raspberry Pi 2 or 3, __**[[: | ||
* Rocrail Server with MBUS as controller (Assuming CAN0 as device.) | * Rocrail Server with MBUS as controller (Assuming CAN0 as device.) | ||
- | * __**[[: | + | * __**[[: |
The advantage of this type is the direct Rocrail Server connection with CAN; It can run without EtherNet and USB.\\ | The advantage of this type is the direct Rocrail Server connection with CAN; It can run without EtherNet and USB.\\ | ||
The WiFi on the **Raspberry Pi 3 B+** can be used for visualisation by Rocview, Rocweb and/or andRoc.\\ | The WiFi on the **Raspberry Pi 3 B+** can be used for visualisation by Rocview, Rocweb and/or andRoc.\\ | ||
Line 78: | Line 72: | ||
If all protocols are disabled in the settings, they will be all activated at startup. At least one protocol must be activated.\\ | If all protocols are disabled in the settings, they will be all activated at startup. At least one protocol must be activated.\\ | ||
- | ====Report state==== | + | \\ |
+ | =====Options===== | ||
+ | {{: | ||
+ | ===Report state=== | ||
Report the current, voltage and temperature of the **[[# | Report the current, voltage and temperature of the **[[# | ||
|< >| | |< >| | ||
Line 86: | Line 83: | ||
| Regular | Report every 5 seconds | For use in combination with the Power Manager | | | Regular | Report every 5 seconds | For use in combination with the Power Manager | | ||
- | \\ | ||
- | ====Options==== | ||
- | {{: | ||
===Slot purge time=== | ===Slot purge time=== | ||
If a locomotive is nonactive for this period of time, and the speed is zero, it will be removed from the refresh cycle to make place for other locomotives.\\ | If a locomotive is nonactive for this period of time, and the speed is zero, it will be removed from the refresh cycle to make place for other locomotives.\\ | ||
Line 101: | Line 95: | ||
===Master=== | ===Master=== | ||
+ | **Note:** MS2 Firmware 3.55 and higher does negotiate different, compared with previous versions. This none conform update will be not supported.\\ | ||
**Note:** //Master mode will be disabled in case a CS2/CS3 is detected.// | **Note:** //Master mode will be disabled in case a CS2/CS3 is detected.// | ||
Puts the connected MS2 in slave mode and provide loco information.\\ | Puts the connected MS2 in slave mode and provide loco information.\\ | ||
Line 129: | Line 124: | ||
All addressing schemes are supported. (FADA/ | All addressing schemes are supported. (FADA/ | ||
The bus value **must** be set to zero.\\ | The bus value **must** be set to zero.\\ | ||
- | ====GC2a==== | ||
- | * Bus = CAN-ID | ||
- | * Address = GC2a port number, 1...16 | ||
- | |||
- | \\ | ||
- | |||
- | =====GC2a Signal support===== | ||
- | This is for simple signals up to 4 LED and max. 5 aspects.\\ | ||
- | Only the RED address will be used as offset for all LEDs.\\ | ||
- | |< >| | ||
- | ^ Parameter ^ Description ^ | ||
- | | Control | Aspect numbers | | ||
- | | Port type | LED | | ||
- | | Bus | CAN-ID of the GC2a | | ||
- | | Addressing | FLAT from 1 to 16 - number of aspects | | ||
- | |||
- | ====Aspect Values==== | ||
- | See: __**[[: | ||
- | The number of controlled LEDs will be calculated from the aspect values.\\ | ||
- | |||
- | ===Example=== | ||
- | ===Aspect value examples=== | ||
- | |< >| | ||
- | ^ Value (dec) ^ LEDs ^ | ||
- | | 0x01 (1) | LED 1 on | | ||
- | | 0x02 (2) | LED 2 on | | ||
- | | 0x04 (4) | LED 3 on | | ||
- | | 0x08 (8) | LED 4 on | | ||
- | | 0x11 (17) | LED 1 blinking | | ||
- | | 0x55 (85) | LED 1 and 3 blinking | | ||
- | | 0x03 (3) | LED 2 and LED 1 on | | ||
- | | 0x13 (19) | LED 2 on and LED 1 blinking | | ||
- | |||
\\ | \\ | ||
=====Tips===== | =====Tips===== | ||
- | * Note: In order to show changes of loco functions in Rocview option **[[: | + | * Note: In order to show changes of loco functions in Rocview, option **[[: |
mbus/mbus-en.txt · Last modified: 2022/02/10 22:05 by rjversluis