Differences

This shows you the differences between two versions of the page.

--- mbus:mbus-en [2019/07/29 20:24] – [Type] phg
+++ mbus:mbus-en [2020/04/18 16:21] – [Tips] phg
@@ Line 10: / Line 10: @@
 The Command Station, Märklin TrackBox(GleisBox), is economically priced and supports the digital **DCC/MfX/MM2** protocols. A Mobile Station can be used as throttle and programmer.\\
-====Overview====
-{{mbus:mbus-socketcan.jpeg?400}}\\
 ====Devices====
-{{ :arduino:gc2a-module.jpg?200}}{{ :mbus:ms2.png}}
+{{ :mbus:ms2.png}}
   * Raspberry Pi + Rocrail Server + __**[[:rocnet:pi01can-en|Pi01CAN]]**__ or __**[[:cbus:socketcan-en|RPI-CAN]]**__
   * or Banana Pi M1 + Rocrail Server + [[http://lnxpps.de/bpi/|BPi CAN]]
-  * __**[[:arduino:rcan-en|CANGC2a]]**__ 16 I/O
   * Märklin TrackBox(GleisBox) [[https://www.maerklin.de/de/produkte/details/article/60116|60116]] [[https://www.maerklin.de/de/produkte/details/article/60113|60113]]
   * Märklin Mobile Station [[https://www.maerklin.de/de/produkte/details/article/60657|60657]] (Optional)
@@ Line 30: / Line 27: @@
 //"For small systems."//\\
 The company [[https://www.gridconnect.com|Grid Connect]] defined an ASCII framing protocol designed for using frames over serial connections.\\
-The USB connection of the __**[[:arduino:rcan-en|CANGC2a]]**__ can be used for this type.\\
 Fixed baud rate of 500000.\\
 ===SocketCAN===
@@ Line 99: / Line 95: @@
 ===Master===
-**Note:** MS2 Firmware 3.55 does negotiate different compared with previous versions. (Not supported yet.)\\
+**Note:** MS2 Firmware 3.55 and higher does negotiate different, compared with previous versions. This none conform update will be not supported.\\
 **Note:** //Master mode will be disabled in case a CS2/CS3 is detected.//\\
 Puts the connected MS2 in slave mode and provide loco information.\\
@@ Line 128: / Line 124: @@
 All addressing schemes are supported. (FADA/PADA/MADA)\\
 The bus value **must** be set to zero.\\
-====GC2a====
-  * Bus = CAN-ID
-  * Address = GC2a port number, 1...16
- \\
-=====GC2a Signal support=====
-This is for simple signals up to 4 LED and max. 5 aspects.\\
-Only the RED address will be used as offset for all LEDs.\\
-|< >|
-^ Parameter ^ Description ^
-| Control | Aspect numbers |
-| Port type | LED |
-| Bus | CAN-ID of the GC2a |
-| Addressing | FLAT from 1 to 16 - number of aspects |
-====Aspect Values====
-See: __**[[:signal-props-en#value|Aspect Values]]**__ \\
-The number of controlled LEDs will be calculated from the aspect values.\\
-===Example===
-===Aspect value examples===
-|< >|
-^ Value (dec) ^ LEDs ^
-| 0x01 (1) | LED 1 on |
-| 0x02 (2) | LED 2 on |
-| 0x04 (4) | LED 3 on |
-| 0x08 (8) | LED 4 on |
-| 0x11 (17) | LED 1 blinking |
-| 0x55 (85) | LED 1 and 3 blinking |
-| 0x03 (3) | LED 2 and LED 1 on |
-| 0x13 (19) | LED 2 on and LED 1 blinking |
  \\
 =====Tips=====
-  * Note: In order to show changes of loco functions in Rocview option **[[:rocrailini-automode-en#allow_zero_throttle_id|Allow Zero Throttle ID]]** has to be activated.
+  * Note: In order to show changes of loco functions in Rocview, option **[[:rocrailini-automode-en#allow_zero_throttle_id|Allow Zero Throttle ID]]** has to be activated.