This is an old revision of the document!


ORD-VC-1 Universal booster with adjustable output between 1,6 AND 25 Amp.

ContentHardwareGCA


By Peter Giling


Description

With the avaiable high power bridges, it was obvious to start doing something with it.
This booster will put all previous boosters from GCA in the background.
It is very small, only 70 x 60 x 50 mm, and can be used from 1 to Z scale.
The base of this booster is an IBT-2 bridge unit.
This unit has a maximum power option to 42 Amp, but this booster is designed not to handle more than 25 Amp.
Short circuit shut off is handled on-board and maximum current is selectable by dip switch. (See below)
On top of IBT-2 unit a board is situated that has all the necessary equipment for booster function.
This board contains two small processors and various opto-couplers for isolated input and output.
Booster also has so-called cut-out for use with Railcom
Processor IC1 is controlling the output pulses, and will switch off when pulses are incorrect or not available.
Processor IC1 also handles the cut-out for Railcom.
Processor IC5 handles the maximum seelcted current.
When the output exceeds the selected value, booster is shut off, and will try to start again every second.
Inputs for LocoNet Railsync, DCC232 (direct drive inside Rocrail) and CDE (lenz).
Also any central station can be used to drive this booster.
Power for this booster should be a DC output power supply, and the maximum Amp output of this power supply should be
ALWAYS slightly more than the selected Amp on booster.
The long run test prooves that it is absolutely necessary to use a small fan for cooling , when the booster does more than 10 Amps.
So a small fan was added, which kept it below 40°C.
But on the maximum load of 25 Amp, a larger fan is undoubtly needed.
Also, the position of the unit, where air can freely stream in upside direction through the cooling grid is essential.

Features

  • Useable for Railcom
  • Easy selectable maximum output current.
  • Input for Railsync (LocNet)
  • Input for DCC232 (inside Rocrail, no central station needed.
  • With extra adapter also useable for DCC232 via USB.
  • Input for CDE (Lenz)
  • Only extra cooling needed, if contineous output is more that 16 Amp.(Can be done by small 40×40 mm fan,)
  • All signal inputs are isolated.
  • Absolute maximum power input 24Vdc.
  • also available without Railcom

The hardware.

Frimware

Hex files for Chip type
IC1 ord-vc-1_ic1_firmware.zip PIC12F629
IC5 ord-vc-1_ic5.zip PIC12F675



Test in Deventer succesfull

On March 24 & 25 2018, I used this booster for a two day test outside, with an EMD GP9 G-track locomotive, ZIMO sound decoder and with full smoke generator in function.
Not really everybody was happy with my sound and smoke, but that is besides the point.
It worked absolutely without any problem.


Current selection (IMPORTANT!)

Since this unit can handle a large current , it is necessary to select the maximum current output.
For example: If you use a power supply of 18V 4 Amp, the selection should be maximum 3 Amp on the booster.
When power supply can not handle the maximum selected current, the booster will not be able to shut off when a short
circuit occured.
This can cause much damage to your materials, and maybe fire hazard.

Current selection table (also printed on-board)
Amp max Dipswitch
1 2 3
1,6 OFF OFF OFF
3 OFF OFF ON
5 OFF ON OFF
8 OFF ON ON
10 ON OFF OFF
16 ON OFF ON
20 ON ON OFF
25 ON ON ON


Using multiple boosters.

It might be a bit overdone, but if the need for multiple boosters is there, be sure not to mix standard boosters with Railcom booster like ORD-VC-1.
That mix is NOT possible.


Personal Tools