User Tools

Site Tools


roco:roco-z21-en

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
roco:roco-z21-en [2018/12/08 07:53]
rjversluis [Accessories]
roco:roco-z21-en [2019/05/12 02:40] (current)
rainerk [Xpressnet GBM]
Line 52: Line 52:
 ====Xpressnet GBM==== ====Xpressnet GBM====
 This option must be set if RailCom detectors are connected to the Xpressnet bus of the z21.\\ This option must be set if RailCom detectors are connected to the Xpressnet bus of the z21.\\
-(Blücher GBM16XN)\\ +(Blücher GBM16XN) 
 + \\ 
 +==== Report absent ==== 
 +If this option is activated, it will be reported if a loco ID is no longer recognized by a RailCom detector. 
 +  \\
 ====Program FB==== ====Program FB====
 {{ :​roco:​z21-10787.jpg?​400}} {{ :​roco:​z21-10787.jpg?​400}}
Line 78: Line 81:
 ^ Bus ^ Network ^ Z21 Firmware ^ Remark ^ ^ Bus ^ Network ^ Z21 Firmware ^ Remark ^
 |  0 | R-Bus |  1.0  | | |  0 | R-Bus |  1.0  | |
-|  1 | LocoNet ​Input |  1.2  | LocoIO, DR5088RC(Feedback) ​+|  1 | LocoNet |  1.2  | LocoIO, DR5088RC(Feedback)GBM16XN, DR5088RC(Block) |
-|  1 | LocoNet Multi Sense |  1.2  | GBM16XN, DR5088RC(Block) |+
 |  3 | CAN |  1.29  | Roco Z21 CAN Detector | |  3 | CAN |  1.29  | Roco Z21 CAN Detector |
 ===Flat addressing=== ===Flat addressing===
Line 86: Line 88:
 ...\\ ...\\
  \\  \\
- 
 ====Special Feature ==== ====Special Feature ====
 In the default setting of the z21 / Z21 there is an address offset of +4 between Multimaus and Rocrail. This means that in Rocrail the addresses 1-4 can not be used. If e.g. address 1 of the multimouse is to be used in Rocrail address 5. But there is an elegant way to eliminate this shift. To do this, connect the z21 to the computer via the z21-maintenance-tool,​ activate the option "​DCC-switch address shift +4" resp. "DCC tournout-addressing according to RCN-213"​ on the "​Settings"​ tab and then confirm with "​Write"​. Then the addresses from 1 can also be used in Rocrail. Addressing is done exclusively according to FADA (flat addressing). \\ In the default setting of the z21 / Z21 there is an address offset of +4 between Multimaus and Rocrail. This means that in Rocrail the addresses 1-4 can not be used. If e.g. address 1 of the multimouse is to be used in Rocrail address 5. But there is an elegant way to eliminate this shift. To do this, connect the z21 to the computer via the z21-maintenance-tool,​ activate the option "​DCC-switch address shift +4" resp. "DCC tournout-addressing according to RCN-213"​ on the "​Settings"​ tab and then confirm with "​Write"​. Then the addresses from 1 can also be used in Rocrail. Addressing is done exclusively according to FADA (flat addressing). \\
  \\  \\
  
-=====Rocrail & GBM16XN=====+=====GBM16XN===== 
 +| :!: **Activate only in case of GBM16XN detectors!** | 
 +This option will activate evaluating LAN_LOCONET_DETECTOR messages to support the GBM16XN detectors.\\ 
 +The reported input address is increased with one to meet the GBM16XN settings. This conflicts with normal LocoNet!\\
 Z21 firmware: 1.24+\\ Z21 firmware: 1.24+\\
-See for setup: http://​www.z21.eu/​content/​download/​1134/​12993/​file/​Z21_GBM16XN.pdf \\ 
  
  
  \\  \\
 +===== Power Manager=====
 +To add the Z21 to the __**[[:​powerman-en|Power Manger]]**__:​\\
 +{{roco:​z21-booster-en.png}}\\
 +The address is fixed to 21, Interface ID is optional.\\
 +{{roco:​z21-powerman-en.png}}\\
  
 + \\
 +=====CAN Detector=====
 +Disable all emulation with the Z21 Maintenance Tool to prevent unwanted events:\\
 +{{:​roco:​z21-maintenance-de.png?​0x400}}\\
 +
 + \\
 ===== Trouble Shooting ===== ===== Trouble Shooting =====
 ==== LAN ==== ==== LAN ====
roco/roco-z21-en.1544252000.txt.gz · Last modified: 2018/12/08 07:53 by rjversluis