Innovative Model Railroad Control System

User Tools

Site Tools

Trace:
route-perm-en

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
route-perm-en [2019/07/16 10:26] – [Length] peter_bastiroute-perm-en [2023/06/26 15:42] (current) – rjversluis
Line 10: Line 10:
    
  
-{{route-perm-en.png?800}}+{{route-perm-en.png?801}}
  \\  \\
  
-^ :!: Caution in dealing with permissions! Only set when really needed and desired. Failure to correctly set permissions mean that trains do not find a destination and are a recurring theme in the forum.  ^+^ :!: Caution in dealing with permissions! Only set when really needed and desired. Failure to correctly set permissions mean that trains do not find a destination and are a recurring theme in the forum.  \\ \\ :!: Set __permissions are always restrictions__ compared to the standard settings. If it is not possible to drive without permissions, setting additional permissions is not a solution, but rather makes the problem worse! ^
  
  \\  \\
Line 21: Line 21:
 To prevent certain **[[:loc-index-en|Locomotives]]** and or **[[:operator-consist-en|Trains]]** using a route this tab can be used to define which are permitted or not.\\ To prevent certain **[[:loc-index-en|Locomotives]]** and or **[[:operator-consist-en|Trains]]** using a route this tab can be used to define which are permitted or not.\\
 The include list is evaluated first. If empty the exclude list is evaluated.\\ The include list is evaluated first. If empty the exclude list is evaluated.\\
 +   - The list "Include" is evaluated with priority. If locomotives or trains are entered here, the route can __only__ be used by these locomotives or trains. \\ Entries in the "Exclude" list are then ignored and for a better overview it is recommended to leave the "Exclude" list empty. \\ 
 +   - The "Exclude" list is only evaluated __if the "Include" list is empty__. Then __only__ locomotives or trains on the "Exclude" list are excluded from using this route. All other locomotives or trains are allowed to use this route.
 > **Note:** Permissions will be respected in **[[:automatic-en#running_without_defined_destination|automatic mode without defined destination]]**. In **[[:automatic-en#running_to_a_defined_destination|automatic mode with defined destination]]**, however, permissions are //not// respected for the destination block and the route to the destination block! Hence, with a given destination it is possible to move a loco or a train into a block by, e.g. drag and drop, although the loco- or train-type is not allowed in this block.  > **Note:** Permissions will be respected in **[[:automatic-en#running_without_defined_destination|automatic mode without defined destination]]**. In **[[:automatic-en#running_to_a_defined_destination|automatic mode with defined destination]]**, however, permissions are //not// respected for the destination block and the route to the destination block! Hence, with a given destination it is possible to move a loco or a train into a block by, e.g. drag and drop, although the loco- or train-type is not allowed in this block. 
  
Line 29: Line 30:
 Specifies which train types are allowed. All are allowed if no train type is selected.\\ Specifies which train types are allowed. All are allowed if no train type is selected.\\
 Further information is found __**[[block_traintype-en|Here]]**__.\\ Further information is found __**[[block_traintype-en|Here]]**__.\\
 + \\
 +====Engine====
 +Specifies which engine types are allowed. All are allowed if no engine type is selected.\\
 +Further information is found __**[[:loc-details-en#engine|Here]]**__.\\
 +
  \\  \\
  
Line 37: Line 43:
 ==== Min. train length ==== ==== Min. train length ====
 If set greater than zero it will be compared with the length of the requesting train.\\ If set greater than zero it will be compared with the length of the requesting train.\\
-The route will not permit it to use when the train length is less then the min. length allowed.+The route will not permit it to use when the train length is less than the min. length allowed.\\
  
 ====Length==== ====Length====
 Length of the route between IN of the starting block and ENTER of the target block \\ Length of the route between IN of the starting block and ENTER of the target block \\
 This length is used for **[[:rocrailini-automode-en#calculate|Realtime Calculation]]** in __**[[:virtual-automatic-en|Virtual Automatic]]**__ only. This length is used for **[[:rocrailini-automode-en#calculate|Realtime Calculation]]** in __**[[:virtual-automatic-en|Virtual Automatic]]**__ only.
-The route length between ENTER and IN of the target block have to be set in the block **[[:block-gen-en#length_between_enter_and_in|length between enter and in]]**+ 
 +> Note: For virtual timing also the block length have to be set in the **[[:block-gen-en#length_between_enter_and_in|block length]]**
 ====Radius==== ====Radius====
 This number reflects the smallest radius of a train, locomotive or wagon that can safely operate in this route. \\ This number reflects the smallest radius of a train, locomotive or wagon that can safely operate in this route. \\
Line 57: Line 64:
  
  \\  \\
-==== Placing ==== +==== Shunting ==== 
-See: __**[[:loc-int-en#placing|Loco Interface]]**__\\+===Yes=== 
 +Allow locos in **[[loc-shunting-en|shunting mode]]**.\\ 
 +===Only=== 
 +Allow locos in shunting mode only.\\ 
 +:!: This option will reject all normal trains to use this route.\\ 
 +===No=== 
 +Disallow locos in shunting mode.\\ 
 +==== Logical direction ==== 
 +See: __**[[:loc-details-en#reset_logical_direction|Loco Interface]]**__\\
 ===Both=== ===Both===
-All placing types are allowed.\\+All logical directions are allowed.\\
 ===Default=== ===Default===
-Only placing default is allowed.\\+Only the default logical direction is allowed.\\
 ===Swapped=== ===Swapped===
-Only placing swapped is allowed.\\+Only the swapped logical direction is allowed.\\
  
  
  \\  \\
 +
 +
 ==== Auto mode ==== ==== Auto mode ====
 ===Both=== ===Both===
Line 75: Line 92:
 ===Random=== ===Random===
 Only trains __without__ running a schedule are allowed.\\ Only trains __without__ running a schedule are allowed.\\
 +===No=== 
 +The route will not be used in automatic mode.\\
  
  \\  \\
route-perm-en.1563265576.txt.gz · Last modified: 2019/07/16 10:26 by peter_basti