signal-int-en
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
signal-int-en [2019/06/02 14:40] – [Function] rjversluis | signal-int-en [2021/12/12 17:48] – [Protocol] rjversluis | ||
---|---|---|---|
Line 31: | Line 31: | ||
====Protocol==== | ====Protocol==== | ||
- | This is control system dependent. Used only for __**[[: | + | This is control system dependent. Used only for __**[[: |
====Dim==== | ====Dim==== | ||
Dimming speed for LED type signals.\\ | Dimming speed for LED type signals.\\ | ||
- | \\ | + | ====Brightness==== |
+ | The brightness in case of type LED.\\ | ||
+ | Supported by: | ||
+ | * LEDii | ||
+ | * WIO (WIP) | ||
+ | |||
+ | ====Parameter==== | ||
+ | Special settings for some Command Stations: | ||
+ | * **[[: | ||
+ | \\ | ||
===== Control ===== | ===== Control ===== | ||
Line 41: | Line 50: | ||
==== Patterns ==== | ==== Patterns ==== | ||
- | Signal decoders are most likely controlled with patterns on two ports. The patterns are set up on the **__[[signal-props-en# | + | Signal decoders are most likely controlled with patterns on two or three ports. The patterns are set up on the **__[[signal-props-en# |
- | See __**[[: | + | See __**[[: |
+ | **Note:** Patterns can only be used with PADA/MADA addressing, and max. 5 aspects. (2.1.601+) __FADA is not supported.__\\ | ||
==== Aspect numbers ==== | ==== Aspect numbers ==== | ||
Line 48: | Line 59: | ||
The following Command Stations are supported: | The following Command Stations are supported: | ||
* [[: | * [[: | ||
- | * [[: | + | |
+ | | ||
* [[: | * [[: | ||
- | * [[: | + | * [[: |
* [[: | * [[: | ||
* [[: | * [[: | ||
* [[: | * [[: | ||
* [[: | * [[: | ||
+ | * [[: | ||
| | ||
- | ¹) [[http:// | + | |
==== Linear ==== | ==== Linear ==== | ||
Uses only the first address as offset to control all aspects. (Only for FADA/ | Uses only the first address as offset to control all aspects. (Only for FADA/ | ||
Line 74: | Line 87: | ||
====Function==== | ====Function==== | ||
Uses mobile decoder function outputs for LED signals.\\ | Uses mobile decoder function outputs for LED signals.\\ | ||
- | The red address field value is used to address the mobile decoder.\\ | + | The red address field value is used to address the mobile decoder. The port is the function number: 0...32.\\ |
Up to 4 aspects are supported.\\ | Up to 4 aspects are supported.\\ | ||
- | The white aspect can be used to control the red/ | + | The white aspect can be used to control the red/ |
+ | |< >| | ||
+ | ^ Bit ^ Bulb ^ | ||
+ | | 0x01 | red | | ||
+ | | 0x02 | green | | ||
+ | | 0x04 | yellow | ||
\\ | \\ | ||
=====Accessory===== | =====Accessory===== | ||
+ | |< >| | ||
^ Command Station ^ Remark ^ | ^ Command Station ^ Remark ^ | ||
| __**[[: | | __**[[: |
signal-int-en.txt · Last modified: 2023/09/12 08:11 by rjversluis