signal-int-en
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
signal-int-en [2020/04/04 08:20] – [Patterns] rjversluis | signal-int-en [2023/09/12 08:11] (current) – [Aspect numbers] rjversluis | ||
---|---|---|---|
Line 4: | Line 4: | ||
[[english|Content]] -> [[english# | [[english|Content]] -> [[english# | ||
* [[signal-index-en|Index]] | [[signal-gen-en|General]] | **[[: | * [[signal-index-en|Index]] | [[signal-gen-en|General]] | **[[: | ||
- | * [[signal-setup-en|Signal Setup]] | + | * [[signal-setup-en|Signal Setup]] | [[: |
// \\ // \\ | // \\ // \\ | ||
Line 16: | Line 16: | ||
=====Addressing===== | =====Addressing===== | ||
- | ====Interface ID==== | + | =====Interface ID===== |
- | If more than one Command Station (CS) is defined in Rocrail __and__ | + | If more than one command station |
====Bus==== | ====Bus==== | ||
Line 31: | Line 31: | ||
====Protocol==== | ====Protocol==== | ||
- | This is control system dependent. Used only for __**[[: | + | This is control system dependent. Used only for __**[[: |
====Dim==== | ====Dim==== | ||
Dimming speed for LED type signals.\\ | Dimming speed for LED type signals.\\ | ||
Line 39: | Line 39: | ||
* LEDii | * LEDii | ||
* WIO (WIP) | * WIO (WIP) | ||
- | \\ | + | |
+ | ====Parameter==== | ||
+ | Special settings for some Command Stations: | ||
+ | * **[[: | ||
+ | \\ | ||
===== Control ===== | ===== Control ===== | ||
Line 48: | Line 52: | ||
Signal decoders are most likely controlled with patterns on two or three ports. The patterns are set up on the **__[[signal-props-en# | Signal decoders are most likely controlled with patterns on two or three ports. The patterns are set up on the **__[[signal-props-en# | ||
See __**[[: | See __**[[: | ||
- | **Note:** Patterns can only be used with MADA addressing, and max. 5 aspects. (2.1.601+)\\ | + | **Note:** Patterns can only be used with PADA/MADA addressing, and max. 5 aspects. (2.1.601+) |
Line 54: | Line 58: | ||
Use the aspect numbers specified on the detail tab for the accessory command.\\ | Use the aspect numbers specified on the detail tab for the accessory command.\\ | ||
The following Command Stations are supported: | The following Command Stations are supported: | ||
+ | * [[: | ||
* [[: | * [[: | ||
- | * [[: | + | * [[: |
- | * [[: | + | * [[: |
* [[: | * [[: | ||
- | * [[: | + | * [[: |
* [[: | * [[: | ||
* [[: | * [[: | ||
* [[: | * [[: | ||
* [[: | * [[: | ||
+ | * [[: | ||
+ | * [[: | ||
| | ||
- | ¹) [[http:// | + | |
==== Linear ==== | ==== Linear ==== | ||
Uses only the first address as offset to control all aspects. (Only for FADA/ | Uses only the first address as offset to control all aspects. (Only for FADA/ |
signal-int-en.1585981202.txt.gz · Last modified: 2020/04/04 08:20 by rjversluis