User Tools

Site Tools


switch-int-en

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
switch-int-en [2020/02/12 19:00] – [Multiple switches at the same decoder output] smitt48switch-int-en [2023/10/19 12:23] (current) rjversluis
Line 3: Line 3:
 [[english|Content]] -> [[english#objects|Objects]] -> **[[switch-en|Switches]]** [[english|Content]] -> [[english#objects|Objects]] -> **[[switch-en|Switches]]**
  
-  * [[switch-index-en|Index]] | [[switch-gen-en|General]] |  **[[switch-int-en|Interface]]** | [[switch-wiring-en|Wiring]] | [[switch-ctrl-en|Control]] | [[switch-frog-en|Frog]] | [[switch-td-en|Trackdriver]] | [[switch-usage-en|Usage]]+  * [[switch-index-en|Index]] | [[switch-gen-en|General]] |  **[[switch-int-en|Interface]]** | [[switch-wiring-en|Wiring]] | [[switch-ctrl-en|Control]] | [[switch-frog-en|Frog]] | [[switch-td-en|Trackdriver]] | [[switch-usage-en|Usage]] | [[switch-menu-en|Menu]]
  
 // \\ // \\ // \\ // \\
Line 9: Line 9:
  
 Switch Dialog Interface Tab.\\ Switch Dialog Interface Tab.\\
-{{:switch-int-en.png}}+{{:switch-int-en.png?800}}
  
  \\  \\
  
 =====Interface ID===== =====Interface ID=====
-If more than one Command Station (CS) is defined in Rocrail __and__ the switch is not wired to the first (defaultCS this field must be used to link this switch with a specific CSOtherwise to be left blank! +If more than one command station is used, then the command station that is responsible for controlling the switch-decoder is specified in this field. The "Interface identifier" field can remain empty if the object is connected to the first command station (first 'digint' in rocrail.inifrom the list of command stations.
- +
- \\ +
 =====Bus===== =====Bus=====
 See: **[[:addressing-en#bus|Addressing]]** See: **[[:addressing-en#bus|Addressing]]**
Line 44: Line 41:
   * **[[:dinamo-om32-en|OM32]]** RS485   * **[[:dinamo-om32-en|OM32]]** RS485
   * **[[:bidib-examples-en#example_servo|BiDiB]]**   * **[[:bidib-examples-en#example_servo|BiDiB]]**
-  * DCC++ IFLAG+  * **[[:dccpp:dccpp-en#options1|DCC++]]**
  
  
Line 78: Line 75:
  
 =====Switch time===== =====Switch time=====
 +:!: Activate this timer in case the motor does not switch itself off!\\
 Some Command Stations allow to define a switch activation time. Check your manual for details. Some Command Stations allow to define a switch activation time. Check your manual for details.
 The time here is in ms.\\ The time here is in ms.\\
 +| Tip: It is much safer to define coil power off in the decoder instead of relying on a second command which could be missed by the decoder and overheat the coil. |
  
 ====Synchronise==== ====Synchronise====
Line 125: Line 124:
  
  \\  \\
 +=====Parameter=====
 +Parameter is used to affect servo bouncing in the **[[wio:wiopico-en|SIOpico]]**.
 +
 +
 + \\
 +=====3W OneServo=====
 +Using just one servo for a 3W is very common for car systems.\\
 +
 +Setup by setting the Address an Port for both motors the same, and select Type Servo.\\
 +
 +|< >|
 +^ Position ^ Field ^ Remark ^
 +| Right | Param 1 |
 +| Straight | Value 1 | If zero the value will be calculated. |
 +| Left  | Param 2 |
 +
 +
 +
 +
  
  
switch-int-en.1581530422.txt.gz · Last modified: 2020/02/12 19:00 by smitt48