Differences

This shows you the differences between two versions of the page.

--- arduino:wio-setup-en [2025/05/26 08:04] – [CVs] rjversluis
+++ arduino:wio-setup-en [2025/10/29 07:51] (current) – rjversluis
@@ Line 4: / Line 4: @@
 [[:wio:overview-en|{{ :wio:wiologo.png}}]]
 **[[:wio:overview-en|WIO Overview]]**
-  * **[[:arduino:wio-setup-en|WIO Setup]]** | [[:arduino:wioctrl-en|WIO Control]] | [[:arduino:amp-en|User Bitmaps]] | [[:arduino:wio-en|WIO Firmware]] | [[:wio:wio-ledscript-en|LEDScript]]
+  * **[[:arduino:wio-setup-en|WIO Setup]]** | [[:arduino:wioctrl-en|WIO Control]] | [[:arduino:amp-en|User Bitmaps]] | [[:arduino:wio-en|WIO Firmware]] | [[:wio:wio-ledscript-en|LEDScript]] | [[:wio:wio-ioscript-en|IOScript]]
@@ Line 105: / Line 105: @@
 Count of 100ms for setting the output pulse length.\\
 Also used for dual coil switch motors.\\
+====Block timer====
+The time between the last upper flank and reporting the sensor off.\\
+Default 2 seconds. (2000ms)\\
 ====Port====
@@ Line 354: / Line 358: @@
  \\
-=====OTA from Scratch=====
+====OTA from Scratch====
 To avoid bothering with the needed libraries for the WIO Sketch this {{:wio:rrota.zip|WPS-OTA-Sketch}} can be used for binary OTA:\\
 ( The Sketch can also be downloaded from https://gitlab.com/rocrail/rrota )
@@ Line 375: / Line 379: @@
  \\
+<html><a name="files"/></html>
+=====Files=====
+File management for WIO CAN.\\
+ \\
+<html><a name="iomapping"/></html>
 =====I/O Mapping=====
 {{:arduino:wio-iomapping-en.png?800}}\\
@@ Line 400: / Line 411: @@
  \\
+<html><a name="usercv"/></html>
 =====User CV=====
 ====Interface====
@@ Line 416: / Line 428: @@
 Delete the ''usrcv.bin'' and restore the default value. A WIO reboot can be necessary.\\
-====Location====
+====File location====
 {{ :arduino:usrcv.bin.png?200}}
 The User CVs are saved in the usrcv.bin file.\\
@@ Line 423: / Line 435: @@
 ====CVs====
 |< >|
-^ CV# ^ Description ^ Range ^ Default ^ PicoW ^ ESP32 ^ ESP8266 ^
+^ CV# ^ Description ^ Range ^ Default ^ PicoW ^ ESP32 ^ ESP8266 ^ Remark ^
-|  0  | LED_ShowMode | 0=off, 1=on | 1 |
+|  0  | LED_ShowMode | 0=off, 1=on |  1 | | | | Show onboard LED flashing to show operation mode |
-|  1  | User_Sound | 0=off, 1=on | 0 |
+|  1  | User_Sound | 0=off, 1=on |  0 | | | | User sound over DAC |
-|  1  | Bat_2S_Full  | 0...4095 | | 2520 | 2400 | 630 |
+|  2  | Bat_2S_Full  | 0...4095 | |  2520 |  2400 |  630 |
-|  1  | Bat_2S_Empty | 0...4095 | | 2220 | 1670 | 480 |
+|  3  | Bat_2S_Empty | 0...4095 | |  2220 |  1670 |  480 |
-|  1  | Bat_3S_Full  | 0...4095 | | 3310 | 3170 | 850 |
+|  4  | Bat_3S_Full  | 0...4095 | |  3310 |  3170 |  850 |
-|  1  | Bat_3S_Empty | 0...4095 | | 2680 | 2570 | 690 |
+|  5  | Bat_3S_Empty | 0...4095 | |  2680 |  2570 |  690 |
-|  1  | Bat_4S_Full  | 0...4095 | | 3470 | 3890 | 960 |
+|  6  | Bat_4S_Full  | 0...4095 | |  3470 |  3890 |  960 |
-|  1  | Bat_4S_Empty | 0...4095 | | 3200 | 3090 | 760 |
+|  7  | Bat_4S_Empty | 0...4095 | |  3200 |  3090 |  760 |
-|  1  | Servo_Min_Pulse | | 700 |
+|  8  | Servo_Min_Pulse | 500...1000 |  700 | | | | Check used servo types for the right value |
-|  1  | Servo_Max_Pulse | | 2300 |
+|  9  | Servo_Max_Pulse | 2000...2500 |  2300 | | | | Check used servo types for the right value |
-|  1  | Display_Keypad_Line | 0...7 | 2 |
+|  10  | Display_Keypad_Line | 0...7 |  2 |
+|  11  | Stepper_ISR_US | |  150 | | | | Number of micro seconds for timer interrupt |
+|  12  | Stepper_ISR_Accel | |  50 | | | | Start/end delay (number of steps for accelerate and decelerate) -> range |
+|  13  | Stepper_ISR_Accel_Step | |  15 | | | | Number of ticks before add/subtrackt accelerate and decelerate -> speed |
+|  14  | User_altitude |  |  104 | | | | https://whataltitude.com |
-Battery levels depends on board and used resistors.\\
-The ESP8266 range is 10bit: 0...1023\\
+Battery levels depends on board and used resistors.\\
+The ESP8266 battery range is 10bit: 0...1023\\
+===Battery resistors===
+<code>
+(+)--[100k]--(ain)--[33k]--(-)
+</code>