Differences

This shows you the differences between two versions of the page.

@@ Line 1: / Line 1: @@
+======Dinamo OM32/OC32/PM32======
+[[:english#command_stations|{{  :interface.png}}]][[:english|{{  :rocrail-logo-35.png}}]]
+[[:english|Content]] -> [[:english#command_stations|Command Stations]] ->  **Dinamo**
+  *  [[:dinamo-en|RM-H, RM-U]] | **[[:dinamo-om32-en|OM32/OC32/PM32]]** | [[:dinamo-car-en|MCC Car System]] | [[:stc-en|DTC]]
+ \\
+| {{http://www.vpeb.nl/files/1613/0627/7263/OM32.jpg?300}} | {{http://www.vpeb.nl/files/cache/1486e5a57cdfa9916a941cab39ada8ba_f40.jpg?250}} | {{http://www.vpeb.nl/files/cache/4da4709021baca1c4749c09c2494abe9_f41.jpg?0x200}}|
+|  [[http://www.vpeb.nl/oplossingen/accessoires/om32-serial/|OM32]]((Der OM32 wird nicht mehr hergestellt.))  |  [[http://www.vpeb.nl/oplossingen/accessoires/oc32/|OC32]]((Der OC32 ist der Nachfolger des OM32.))  |  [[http://www.vpeb.nl/oplossingen/treinen/pm32/|PM32]]  |
+ \\
+=====RM-H/U=====
+Library: **[[:dinamo-en|dinamo]]**\\
+Indirectly controlled by the Dinamo interface.
+  * Switches/Outputs -> OM32 protocol
+  * Switches/Outputs as Digital Output -> DO protocol
+  * Switches/Outputs as Virtual Output -> VO protocol
+  * Switches/Outputs as Default -> PM32 protocol
+  * Signals -> Aspects only
+ \\
+=====RS485=====
+[[http://www.vpeb.nl/producten/actuele-producten/oc32/u485/|{{ http://www.vpeb.nl/files/3013/0607/6054/u485.jpg?150}}]]
+Library: **om32**\\
+Baudrate: 9.600, 19.200 or 38.400((The OC32 module is auto-baud. This means it determines the correct bitrate from the received datastream. In order to minimize start-up errors the initial (start-up) bitrate can be configured by the user.))\\
+Directly controlled by a separate RS485 connection.\\
+ \\
+====Addressing====
+| Field ^ Value ^ Range ^
+^ Address | OM32 module number + 1 | 1...8 |
+^ Port    | OM32 output number + 1 | 1...32 |
+ \\
+==== Switches ====
+| |  Type  ||||
+^ Field ^ Motor ^ Servo ^ Lights ^
+| **[[:switch-int-en#parameter_value|Param]]** | PWM straight (0...31)  | Position straight (0...127)  | Aspect (0...12) straight |
+| **[[:switch-int-en#parameter_value|Value]]**  | PWM turnout (0...31)   | Position turnout (0...127) | Aspect (0...12) turnout |\\
+  * Uncheck the __**[[:switch-int-en#accessory|Accessory]]**__ option for selecting the wanted port type.
+  * Check the __**[[:switch-int-en#single_gate|Single Gate]]**__ option if only __one output__ should be addressed, otherwise the next output is used for the **turnout** command. (Dual coil)
+ \\
+====Signals====
+  * __**[[:signal-int-en#aspect_numbers|Aspects]]**__(OC32)
+  * {{:dinamo:oc32_signals.pdf}} (User document for UK signals.)
+ \\
+====Outputs====
+| |  Type  ||||
+^ Field ^ Accessory ^ Motor ^ Servo ^ Lights ^
+| **[[:output-int-en#parameter|Param]]** | Gain  | PWM OFF (0...31)  | Position OFF (0...127)  | Aspect (0...12) OFF |
+| **[[:output-int-en#value|Value]]**  | 1   | PWM ON (0...31)   | Position ON (0...127) | Aspect (0...12) ON |\\
+  * Uncheck the accessory option for selecting the wanted port type.
+  * The __**[[:output-int-en#blink|Blink]]**__ option is available for the accessory port type only.
+ \\
+====Configuration Tools====
+  * [[http://www.vpeb.nl/english/support/oc32-toolkit|Toolkit OC32]]
+ \\