block-routes-en
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
block-routes-en [2019/03/01 01:32] – [Event] rainerk | block-routes-en [2024/01/25 14:43] (current) – rjversluis | ||
---|---|---|---|
Line 2: | Line 2: | ||
[[: | [[: | ||
[[: | [[: | ||
- | * [[block-index-en|Index]] | [[: | + | * [[block-index-en|Index]] | [[: |
* [[block-sensor-en|How many sensors (feedbacks) per block make sense?]] | * [[block-sensor-en|How many sensors (feedbacks) per block make sense?]] | ||
Line 9: | Line 9: | ||
===== BlockDialog Routes Tab. ===== | ===== BlockDialog Routes Tab. ===== | ||
- | {{: | + | {{: |
\\ | \\ | ||
Line 38: | Line 38: | ||
=====Event===== | =====Event===== | ||
Select the event for the sensor. | Select the event for the sensor. | ||
- | * free | + | {{ block: |
* enter | * enter | ||
* enter2pre | * enter2pre | ||
- | * enter2route | + | * enter2route((enter2route is obsolete and was replaced by FiFo blocks. Since it will be removed from Rocrail someday, it should not be used anymore.)) |
* enter2in | * enter2in | ||
* enter2shortin | * enter2shortin | ||
Line 50: | Line 50: | ||
* ident | * ident | ||
* shortin | * shortin | ||
+ | * free | ||
+ | * enter2free | ||
* [empty] - without assignment to an event, usable for locomotive functions. See: **[[# | * [empty] - without assignment to an event, usable for locomotive functions. See: **[[# | ||
For detailed explanation see chapter __**[[: | For detailed explanation see chapter __**[[: | ||
Line 58: | Line 60: | ||
:!: Without occupancy or reservation of the block, the triggering of this sensor also generates the state //GHOST//. | :!: Without occupancy or reservation of the block, the triggering of this sensor also generates the state //GHOST//. | ||
\\ | \\ | ||
+ | * **Note:** See also __**[[route-sensors-en# | ||
==== End pulse (endpulse) ==== | ==== End pulse (endpulse) ==== | ||
| Deprecated and no Forum support. | \\ | | Deprecated and no Forum support. | \\ | ||
Line 66: | Line 69: | ||
\\ | \\ | ||
- | ==== T 2==== | + | ==== T2==== |
"Event timer 2" will be used if this option is activated. | "Event timer 2" will be used if this option is activated. | ||
Line 134: | Line 137: | ||
> **Note:** Contrary to previous revisions, the event timer is not only effective for the **enter2in** event, but also works for a real **in** sensor. \\ When using schedules, if an in delay is specified, this takes preference over the block event timer. Also, when an event timer is specified in the loc properties, this also takes preference over the block event timer, but not over the in delay in a schedule. | > **Note:** Contrary to previous revisions, the event timer is not only effective for the **enter2in** event, but also works for a real **in** sensor. \\ When using schedules, if an in delay is specified, this takes preference over the block event timer. Also, when an event timer is specified in the loc properties, this also takes preference over the block event timer, but not over the in delay in a schedule. | ||
+ | |||
+ | |||
+ | \\ | ||
+ | =====Free at off===== | ||
+ | As alternative to [[: | ||
+ | |||
+ | ====Requirements==== | ||
+ | * The sensor is of type current sense. | ||
+ | * The sensor decoder is debounced. (WIO, CANGC2, GCA50) | ||
+ | * All wagon wheels and axis are conductive. | ||
+ | |||
+ | ====Example==== | ||
+ | The Enter sensor is also used as Free sensor but with option " | ||
+ | {{: | ||
+ | |||
+ | |||
+ | |||
+ |
block-routes-en.1551400324.txt.gz · Last modified: 2019/03/01 01:32 by rainerk