This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
can-gc6-en [2018/11/12 08:56] 127.0.0.1 external edit |
can-gc6-en [2020/07/15 10:48] phg [PSK header connectors] |
||
---|---|---|---|
Line 13: | Line 13: | ||
\\ | \\ | ||
- | =====Firmware Copyright===== | ||
- | Copyright(c) MERG and Rocrail.\\ | ||
- | Commercial use is prohibited.\\ | ||
- | |||
- | \\ | ||
- | |||
===== Features ===== | ===== Features ===== | ||
Line 24: | Line 18: | ||
* Optional external switch position sensors. | * Optional external switch position sensors. | ||
* [[mgv137-en|GCA137]] support for polarisation | * [[mgv137-en|GCA137]] support for polarisation | ||
- | * [[:cbus:cangc6-firmware-en#setup_panel_flim|Interactive comfortable setup]] and mergCBUS FLiM compatible. | + | * [[:cbus:cangc6-firmware-en#setup_panel_flim|Interactive comfortable setup]] and merg CBUS FLiM compatible. |
- | * Compatible 12VDC mergCBUS connector. (J3) | + | * Compatible 12VDC merg CBUS connector. (J3) |
* Opto-isolation for feed-back switches. | * Opto-isolation for feed-back switches. | ||
* Individual direction-speed selection. | * Individual direction-speed selection. | ||
Line 44: | Line 38: | ||
\\ | \\ | ||
^ LED ^ Function ^ Aspect ^ Color ^ | ^ LED ^ Function ^ Aspect ^ Color ^ | ||
- | | L1 | CBUS activity | Random | Red | | + | | L1 | CAN activity | Random | Red | |
| L2 | FLiM learning mode (PB1) | 1Hz | Yellow | | | L2 | FLiM learning mode (PB1) | 1Hz | Yellow | | ||
| L3 | CPU is running | Continuous | Green | | | L3 | CPU is running | Continuous | Green | | ||
Line 56: | Line 50: | ||
\\ | \\ | ||
^ Connector ^ Function ^ remark ^ | ^ Connector ^ Function ^ remark ^ | ||
- | | J1, J2 | 'GCA' CBUS and 12V power | only needed if used in CAN-GC system | | + | | J1, J2 | CAN and 12V power | only needed if used in CAN-GC system | |
| J3 | 'MERG' CBUS and 12V power | only needed if used in MERG Cbus system | | | J3 | 'MERG' CBUS and 12V power | only needed if used in MERG Cbus system | | ||
| S1..S4 | Servo 1...4 | | | | S1..S4 | Servo 1...4 | | | ||
Line 112: | Line 106: | ||
In order to ease making these cables, it is also possible to buy the necessary tool, to create the PSK cables.\\ | In order to ease making these cables, it is also possible to buy the necessary tool, to create the PSK cables.\\ | ||
The best wire to be used with PSK connectors is 0,25 mm².\\ | The best wire to be used with PSK connectors is 0,25 mm².\\ | ||
- | This special plier will be sold for net price of € 18,25 if ordered together with complete kits. {{:mgv:hardware:crimpzange.jpg?200}}\\ | + | This special plier is available for net price of € 20,00 if ordered together with complete kits. {{:mgv:hardware:crimpzange.jpg?200}}\\ |
Just ask [[peter.giling@rocrail.net|peter.]]\\ | Just ask [[peter.giling@rocrail.net|peter.]]\\ | ||
Line 160: | Line 154: | ||
====Save position==== | ====Save position==== | ||
- | The servo positions will be saved in EEPROM after a Power Off message on CBUS.\\ | + | The servo positions will be saved in EEPROM after a Power Off message on CAN BUS.\\ |
\\ | \\ |