User Tools
dccpp:dccpp-signal-en
Differences
This shows you the differences between two versions of the page.
| — |
dccpp:dccpp-signal-en [2018/11/12 08:56] (current) |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== DCC++ Signal Setup Example ====== | ||
| + | [[:english#command_stations|{{ :interface.png}}]][[:english|{{ :rocrail-logo-35.png}}]] | ||
| + | [[:english|Content]] -> **[[:english#command_stations|Command Stations]]** -> **DCC++** | ||
| + | * [[:dccpp:dccpp-en|DCC++]] | ||
| + | * **[[[:dccpp:dccpp-signal-en|Signal Setup Example]]** | ||
| + | \\ | ||
| + | =====Related Wiki Pages===== | ||
| + | * __**[[:dccpp:dccpp-en#g-ash02|DCC++ I/O Setup]]**__ | ||
| + | * __**[[:signal-int-en#aspect_numbers|Signal Aspect Numbers]]**__ | ||
| + | * __**[[:signal-props-en#value|Signal Aspect Values]]**__ | ||
| + | |||
| + | \\ | ||
| + | =====Test Hardware===== | ||
| + | {{ :dccpp:dccpp-signal-test.jpg?300}} | ||
| + | * __**[[:mgv128-en|GCA128L pushbutton testboard for I/O units]]**__ | ||
| + | * __**[[:g_ash02-en|G-ASH01 Shield for Arduino Mega]]**__ | ||
| + | |||
| + | \\ | ||
| + | |||
| + | =====DCC++ I/O===== | ||
| + | Setting port 30, 32, 34 and 36 to **Output** type on connector **I/O 1**:\\ | ||
| + | {{:dccpp:dccpp-signal-iosetup-en.png}}\\ | ||
| + | - Click on the button **I/O 1** to read the current port settings. | ||
| + | - Set port 30, 32, 34 and 36 to type **O**. | ||
| + | - Click on button **Save**. | ||
| + | |||
| + | |||
| + | \\ | ||
| + | |||
| + | =====Signal Interface===== | ||
| + | Set the port addresses on the __**[[:signal-int-en|Signal Interface]]**__ Tab:\\ | ||
| + | {{:dccpp:dccpp-signal-int-setup-en.png}} | ||
| + | - Address RED to 30. | ||
| + | - Address GREEN to 32. | ||
| + | - Address YELLOW to 34. | ||
| + | - Address WHITE to 36. | ||
| + | Select **Aspects Numbers** as control type, and disable the **Accessory** checkbox.\\ | ||
| + | \\ | ||
| + | |||
| + | =====Signal Details===== | ||
| + | The following __**[[:signal-props-en|Signal Details]]**__ must be set according the wanted behaviour for this example:\\ | ||
| + | {{:dccpp:dccpp-signal-details-setup-en.png}}\\ | ||
| + | - Set the number of aspects to 4. | ||
| + | - In the Pattern section set the aspect __**[[:signal-props-en#number|Numbers]]**__ and __**[[:signal-props-en#value|Values]]**__. | ||
| + | |||
| + | \\ | ||
| + | ^ Aspect number ^ Aspect value ^ Activated outputs as defined on the Interface Tab ^ | ||
| + | | 0 | 2 | GREEN (Addr.=32) | | ||
| + | | 1 | 1 | RED (Addr.=30) | | ||
| + | | 2 | 4 | YELLOW (Addr.=34) | | ||
| + | | 3 | 6 | GREEN+YELLOW (Addr.=32+34) | | ||
| + | | 4 | 0 | none | | ||
dccpp/dccpp-signal-en.txt ยท Last modified: 2018/11/12 08:56 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
