User Tools

Site Tools


dinamo-en

Differences

This shows you the differences between two versions of the page.


dinamo-en [2024/11/30 07:24] (current) – created - external edit 127.0.0.1
Line 1: Line 1:
 +======Dinamo======
 +[[:english#command_stations|{{  :interface.png}}]][[:english|{{  :rocrail-logo-35.png}}]]
 +
 +[[english|Content]] -> [[english#command_stations|Command Stations]] ->   **Dinamo**
 +  *  **[[:dinamo-en|RM-H, RM-U]]** | [[:dinamo-om32-en|OM32/OC32/PM32]] | [[:dinamo-car-en|MCC Car System]]
 +
 +// \\ // \\
 +
 +{{:dinamo:rm-u.jpg?0x160}}{{:dinamo:pm44.jpg?0x160}}\\
 + \\
 +=====Introduction=====
 +Dinamo is a track driver system which has a controller for each block to manage Analog and DCC trains.\\
 +
 +====Notes====
 +  - A track drivers system is a compromise between digital and analog technique and has therefore restricted functionality in Rocrail.
 +  - The **[[:stage-en|Staging Block]]** is not supported. 
 +\\
 +
 +=====Setup=====
 +{{:dinamo:dinamo-setup-en.png}}[[:rocrailini-controller-en|{{rocrailini-controller-en.png?0x200}}]]\\
 +Dinamo must be the **first** command station in the __**[[:rocrailini-controller-en|controllerlist]]**__.\\
 +
 +====Port====
 +RS232 or virtual communication port. (COMx, /dev/tty*)\\
 +====Switch time====
 +The default switch time used if the **[[:switch-int-en#switch_time|individual time]]** is set to zero.\\
 +Default = 200ms.\\
 +
 +
 +====Tx pause====
 +Time in a range of 10...100 ms between datagram transmissions.\\
 +
 +====Baudrate====
 +The default is 19200 which can be change by option "S1 38k4" on the interface to 38400; Check the "DinamoConfig" manual.\\
 + \\
 +
 +=====Addressing=====
 +The Dinamo implementation in Rocrail is conform to the general Rocrail **[[addressing-en|addressing]]**.\\
 +Exceptions:
 +  * Trackdrivers are starting at port 0.
 +
 + \\
 +
 +=====Special block and switch settings=====
 +See: [[:block-int-en|Block Track driver]]\\
 +{{:block:block-td-en.png?0x200}}\\
 +
 +====TD====
 +The Dinamo blocks __must__ be flagged with **TrackDriver** option, even if only DCC loco are used.\\
 +====Port====
 +The **Port** should fit your actual wiring for this block; The Address field is not used.\\
 +
 + \\
 +
 +=====Special Loco settings=====
 +See: 
 +  * [[:loc-int-en#mass|Mass]] for simulating CV3/CV4. Must be set > 0 in case of BBT.
 +  * [[:loc-int-en|Loco Interface]]
 +
 +{{:loc:loc-int-en.png?0x200}}\\
 +
 +====DCC====
 +DCC loco are configured as usual with the following restrictions:
 +  * 28 steps only; The speed steps field is ignored.
 +  * Max. 12 functions.
 +
 +====Analog====
 +^ Attribute ^ Remark ^
 +| **Address** | Must be set to zero. |
 +| **Protocol** | **A** = analog |
 +| **Speed steps** | Fixed: Dinamo provides 63 speed steps for analog loco's |
 +| **Mass** | The acceleration of the loco. | \\
 +
 +====Car====
 +See: **[[dinamo-car-en|Dinamo MCC]]**\\
 +
 +
 + \\
 +=====Manual Control=====
 +**[[:blockgroups-en|Block groups]]** can be used for linking blocks for manually controlling locos.\\
 +The blocks must be defined as **[[:block_traintype-en|shunting type]]** in case running automatically concurrently.\\
 +
 + \\
 +
 +
 +===== OM32/OC32/PM32 =====
 +  * Switches/Outputs -> OM32 protocol
 +  * Switches/Outputs as Digital Output -> DO protocol
 +  * Switches/Outputs as Virtual Output -> VO protocol
 +  * Switches/Outputs as Default -> PM32 protocol
 +