User Tools

Site Tools


gca185-en
no way to compare when less than two revisions

Differences

This shows you the differences between two versions of the page.


gca185-en [2018/11/26 02:27] (current) – created - external edit 127.0.0.1
Line 1: Line 1:
  
 +====== GCA185 Arduino Shield for LocoIo  (LocoNet compatible) ======
 + 
 +[[english|{{  rocrail-logo-35.png}}]]
 +
 +[[english|Content]] -> [[hardware-en|Hardware]] -> [[hardware-en#arduino_uno_locoio_shield|GCA]]
 +  *  [[mgv-overview-en|The GCA modules]] 
 +
 + \\
 +
 +^^^^By Peter Giling ^^^^
 +
 +===== Introduction =====
 + 
 +
 +Dani Guisado in Barcelona ( http://www.clubncaldes.com ) found firmware to make an Arduino Uno function as a LocoIo module.\\
 +With addional work within this firmware, he changed that to make it act like a GCA50\\
 +But of course a small interface was needed to adapt to the LocoIo invironment.\\
 +He started the experiments by using a modified GCA50 as an interface, and that prooved to be fine.\\
 +So I made this shield for Arduino Uno, and provided it to Dani as a base of further experiments.\\
 +You can read the results of that on his web-site.\\
 +This board is now available in the same quality as you are used to from GCA.\\
 + 
 +
 +And making it function like a LocoIO module, it again expands the always growing possibilities of Rocrail.\\
 +
 +===== The prototype =====
 +|  {{:gca:gca185_pict01.png}}  |  {{:gca:gca185_pict04.png?0x360}}  |
 +|  The first prototype has been seriously tested in Spain.  \\  (and prooven allright)  |  The professional board is available now!  |
 +|  {{:gca:gca185_pict05.png}}  ||
 +|  The LNet shield with its motherboard  ||
 +
 +===== The hardware =====
 +|  {{:gca:gca185_sch.pdf|Schematic drawing}}  |
 +|  {{:gca185_pcb.pdf|The pc-board and parts positions}}  |
 +|  {{:gca:gca185_gerber.zip|The pcboard in Gerber}}  |
 +|  {{:gca:gca185_parts.pdf|Bill of materials}}  |
 +^ N.B. Only complete ordered kits will be supported! ^
 +===== Jumpers =====
 +The two jumpers onboard are used to specify where power for the GCA185 and the underlying Arduino Uno is coming from.\\
 +Basicly, GCA185 is supplied with 12V from LocoNet bus.\\
 +If Arduino Uno should also be supplied that way, there are two options.:\\
 +^  Jumper  ^  position  ^  Task  ^  remark  ^
 +|  JP1  |  installed  |  12 Volt going to Vin of Arduino Uno  |  Arduino Uno does not need any further supply  |
 +|  JP1  |  not installed  |  VIN of Arduino is not connected to GCA185  |  |
 +|  |  |  |  |
 +|  JP2  |  installed  |  5 Volt from VR1 is used to supply GCA185  |  Arduino Uno does not need any further supply  |
 +|  JP2  |  not installed  |  5 V  for GCA185 comes from Arduino Uno  |   Supply from VR1 is only used for  J5 and J6 interface connectors. |
 +
 +Further questions?  Ask [[peter.giling@rocrail.net|Peter]].
 +\\
 +
 +===== Firmware for Arduino =====
 +{{:gca:locoino.zip|The Arduino Uno sketch}}\\
 +More info about this development can be found at  http://www.clubncaldes.com.
 +\\
gca185-en.txt · Last modified: 2018/11/26 02:27 by 127.0.0.1