User Tools

Site Tools


mbus:mbus-en

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
mbus:mbus-en [2019/07/29 20:24]
phg [Type]
mbus:mbus-en [2020/04/18 16:21] (current)
phg [Tips]
Line 10: Line 10:
 The Command Station, Märklin TrackBox(GleisBox),​ is economically priced and supports the digital **DCC/​MfX/​MM2** protocols. A Mobile Station can be used as throttle and programmer.\\ The Command Station, Märklin TrackBox(GleisBox),​ is economically priced and supports the digital **DCC/​MfX/​MM2** protocols. A Mobile Station can be used as throttle and programmer.\\
  
-====Overview==== 
-{{mbus:​mbus-socketcan.jpeg?​400}}\\ 
 ====Devices==== ====Devices====
-{{ :​arduino:​gc2a-module.jpg?​200}}{{ :​mbus:​ms2.png}}+{{ :​mbus:​ms2.png}}
   * Raspberry Pi + Rocrail Server + __**[[:​rocnet:​pi01can-en|Pi01CAN]]**__ or __**[[:​cbus:​socketcan-en|RPI-CAN]]**__   * Raspberry Pi + Rocrail Server + __**[[:​rocnet:​pi01can-en|Pi01CAN]]**__ or __**[[:​cbus:​socketcan-en|RPI-CAN]]**__
   * or Banana Pi M1 + Rocrail Server + [[http://​lnxpps.de/​bpi/​|BPi CAN]]    * or Banana Pi M1 + Rocrail Server + [[http://​lnxpps.de/​bpi/​|BPi CAN]] 
-  * __**[[:​arduino:​rcan-en|CANGC2a]]**__ 16 I/O 
   * Märklin TrackBox(GleisBox) [[https://​www.maerklin.de/​de/​produkte/​details/​article/​60116|60116]] [[https://​www.maerklin.de/​de/​produkte/​details/​article/​60113|60113]]   * Märklin TrackBox(GleisBox) [[https://​www.maerklin.de/​de/​produkte/​details/​article/​60116|60116]] [[https://​www.maerklin.de/​de/​produkte/​details/​article/​60113|60113]]
   * Märklin Mobile Station [[https://​www.maerklin.de/​de/​produkte/​details/​article/​60657|60657]] (Optional)   * Märklin Mobile Station [[https://​www.maerklin.de/​de/​produkte/​details/​article/​60657|60657]] (Optional)
Line 30: Line 27:
 //"For small systems."//​\\ //"For small systems."//​\\
 The company [[https://​www.gridconnect.com|Grid Connect]] defined an ASCII framing protocol designed for using frames over serial connections.\\ The company [[https://​www.gridconnect.com|Grid Connect]] defined an ASCII framing protocol designed for using frames over serial connections.\\
-The USB connection of the __**[[:​arduino:​rcan-en|CANGC2a]]**__ can be used for this type.\\ 
 Fixed baud rate of 500000.\\ Fixed baud rate of 500000.\\
 ===SocketCAN=== ===SocketCAN===
Line 99: Line 95:
  
 ===Master=== ===Master===
-**Note:** MS2 Firmware 3.55 does negotiate different compared with previous versions. ​(Not supported ​yet.)\\+**Note:** MS2 Firmware 3.55 and higher ​does negotiate differentcompared with previous versions. ​This none conform update will be not supported.\\
 **Note:** //Master mode will be disabled in case a CS2/CS3 is detected.//​\\ ​ **Note:** //Master mode will be disabled in case a CS2/CS3 is detected.//​\\ ​
 Puts the connected MS2 in slave mode and provide loco information.\\ Puts the connected MS2 in slave mode and provide loco information.\\
Line 128: Line 124:
 All addressing schemes are supported. (FADA/​PADA/​MADA)\\ All addressing schemes are supported. (FADA/​PADA/​MADA)\\
 The bus value **must** be set to zero.\\ The bus value **must** be set to zero.\\
-====GC2a==== 
-  * Bus = CAN-ID 
-  * Address = GC2a port number, 1...16 
- 
- \\ 
- 
-=====GC2a Signal support===== 
-This is for simple signals up to 4 LED and max. 5 aspects.\\ 
-Only the RED address will be used as offset for all LEDs.\\ 
-|< >| 
-^ Parameter ^ Description ^ 
-| Control | Aspect numbers | 
-| Port type | LED | 
-| Bus | CAN-ID of the GC2a | 
-| Addressing | FLAT from 1 to 16 - number of aspects | 
- 
-====Aspect Values==== 
-See: __**[[:​signal-props-en#​value|Aspect Values]]**__ \\ 
-The number of controlled LEDs will be calculated from the aspect values.\\ 
- 
-===Example=== 
-===Aspect value examples=== 
-|< >| 
-^ Value (dec) ^ LEDs ^ 
-| 0x01 (1) | LED 1 on | 
-| 0x02 (2) | LED 2 on | 
-| 0x04 (4) | LED 3 on | 
-| 0x08 (8) | LED 4 on | 
-| 0x11 (17) | LED 1 blinking | 
-| 0x55 (85) | LED 1 and 3 blinking | 
-| 0x03 (3) | LED 2 and LED 1 on | 
-| 0x13 (19) | LED 2 on and LED 1 blinking | 
- 
  
  \\  \\
  
 =====Tips===== =====Tips=====
-  * Note: In order to show changes of loco functions in Rocview option **[[:​rocrailini-automode-en#​allow_zero_throttle_id|Allow Zero Throttle ID]]** has to be activated.+  * Note: In order to show changes of loco functions in Rocviewoption **[[:​rocrailini-automode-en#​allow_zero_throttle_id|Allow Zero Throttle ID]]** has to be activated.
mbus/mbus-en.1564424649.txt.gz · Last modified: 2019/07/29 20:24 by phg