robvrs:g-semaphore-en
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| robvrs:g-semaphore-en [2022/08/27 15:31] – [Notes] rjversluis | robvrs:g-semaphore-en [Unknown date] (current) – removed - external edit (Unknown date) 127.0.0.1 | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | [[: | ||
| - | ======WIO G-Semaphore====== | ||
| - | [[: | ||
| - | * **[[: | ||
| - | |||
| - | {{ : | ||
| - | \\ | ||
| - | //Just a fun semaphore not related to the real semaphores found along railroad tracks.//\\ | ||
| - | \\ | ||
| - | =====Description===== | ||
| - | A WIOesp based stand alone semaphore.\\ | ||
| - | The Lolin D32 is selected because it has an onboard battery management for charging and discharging.\\ | ||
| - | |||
| - | The WIO type should be set to Servo and NeoPixel will be activated on demand for the WS2811 color LED.\\ | ||
| - | |||
| - | \\ | ||
| - | =====OpenSCAD===== | ||
| - | {{ : | ||
| - | The 3D files for the semaphore: | ||
| - | * https:// | ||
| - | * https:// | ||
| - | **Note 1:** Print all components separately.\\ | ||
| - | **Note 2:** Rotate the pole in Cura by 45° to fit on the print bed.\\ | ||
| - | |||
| - | \\ | ||
| - | =====Filament===== | ||
| - | PETG is selected for outdoor usage.\\ | ||
| - | |||
| - | ^ Part ^ Color ^ | ||
| - | | Bottom | Grey | | ||
| - | | Top | Grey | | ||
| - | | Pole | Military green | | ||
| - | | Arm | White | | ||
| - | | Warn board | White | | ||
| - | | Arm Red | Red | | ||
| - | | Warn Red | Red | | ||
| - | |||
| - | \\ | ||
| - | =====Wiring===== | ||
| - | {{: | ||
| - | ^ Component ^ Lolin D32 pin ^ Remark ^ | ||
| - | | Servo PWM | 12 | A 270 Ohm resistor should be inserted between servo and Lolin D32 | | ||
| - | | Servo(+) | BAT | | ||
| - | | Servo(-) | GND | | ||
| - | | [[: | ||
| - | | WS2811(+) | BAT | | ||
| - | | WS2811(-) | GND | | ||
| - | | 3V7 Battery(+) | - | Connect to the flip switch | | ||
| - | | 3V7 Battery(-) | GND | | ||
| - | | Flip switch | BAT | Other switch connection goes to the Battery(+) | | ||
| - | |||
| - | ====Battery==== | ||
| - | Li-Ion 3V7 example common use for wireless telephones: | ||
| - | {{: | ||
| - | |||
| - | \\ | ||
| - | =====IOScript===== | ||
| - | IOScript ON: | ||
| - | < | ||
| - | 00 1 S 000 000 0 02 | ||
| - | 00 1 P 000 100 0 01 255 000 000 | ||
| - | </ | ||
| - | Dateiname: '' | ||
| - | |||
| - | IOScript OFF: | ||
| - | < | ||
| - | 00 1 S 000 060 0 02 | ||
| - | 00 1 P 000 100 0 01 000 255 000 | ||
| - | </ | ||
| - | Dateiname: '' | ||
| - | |||
| - | \\ | ||
| - | =====Signal Setup===== | ||
| - | ====Interface==== | ||
| - | |< >| | ||
| - | ^ Fiels ^ Value ^ Remark ^ | ||
| - | | Interface ID | WIO | | ||
| - | | Node ID | 41 | WIO setup dependent. | | ||
| - | | RED Address: | ||
| - | | Control | Default | | ||
| - | | Type | Macro | To trigger IOScript on the WIO. | | ||
| - | |||
| - | |||
| - | ====Details==== | ||
| - | |< >| | ||
| - | ^ Fiels ^ Value ^ Remark ^ | ||
| - | | Signal type | * | SVG Theme dependent. | | ||
| - | | Aspects | 2 | | ||
| - | |||
| - | \\ | ||
| - | =====Notes===== | ||
| - | * Not all photos and images represent the latest developments of the semaphore. | ||
| - | * Use 0,05mm² decoder wire. | ||
| - | * The standard servo arm must be cut to fit. | ||
| - | * Print the pole without support to be able to push cable for the WS2811 through it. | ||
| - | |||
| - | \\ | ||
| - | =====Links===== | ||
| - | * [[: | ||
| - | * [[: | ||
| - | * [[https:// | ||
| - | |||
| - | |||
robvrs/g-semaphore-en.1661607070.txt.gz · Last modified: 2022/08/27 15:31 by rjversluis