User Tools
rocview:cmdrecorder-en
Differences
This shows you the differences between two versions of the page.
|
rocview:cmdrecorder-en [2018/11/12 08:56] |
rocview:cmdrecorder-en [2018/11/12 08:56] (current) |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== Command Recorder ====== | ||
| + | [[:english#rocview|{{ :viewer.png}}]][[:english|{{ :rocrail-logo-35.png}}]] | ||
| + | [[:english|Content]] -> [[:english#rocview|Rocview ]] | ||
| + | * **Command recorder** | ||
| + | \\ | ||
| + | | //Menu->Control->Command recorder// | | ||
| + | \\ | ||
| + | |||
| + | =====Introduction===== | ||
| + | The command recorder can be used to record basic commands send from Rocview to the server.\\ | ||
| + | {{:rocview:cmdrecorder-en.png}}\\ | ||
| + | |||
| + | \\ | ||
| + | ===== Features ===== | ||
| + | * Record commands as text | ||
| + | * Play back | ||
| + | * Export and import | ||
| + | * Modify, insert and delete commands | ||
| + | * Create route command | ||
| + | * Time stamp option; Must be activated before recording is started. | ||
| + | ====Note==== | ||
| + | * Not all commands are supported. | ||
| + | \\ | ||
| + | |||
| + | =====Record a Route===== | ||
| + | With the following 10 steps a route can be created: | ||
| + | - Make sure Rocview is online. (Connected with the Rocrail server.) | ||
| + | - Reset all involved blocks from occupancy. | ||
| + | - Start recording. | ||
| + | - Click on the start block. -> Use Shift+Click for choosing the plus block side. | ||
| + | - Click on all needed switches, signals and sensors. \\ To get the wanted command correctly in the route use the context menu instead of a single click to select the right command. | ||
| + | - Click on the destination block. -> Use Shift+Click for choosing the plus block side. | ||
| + | - Optional click on the crossing blocks. | ||
| + | - Stop the recording. | ||
| + | - Optional modify some recorded lines. | ||
| + | - Push the **Route** button. | ||
| + | The new route will be shown in the Route Dialog to be able to make some changes or set options if needed.\\ | ||
| + | After pushing the OK button the recorded route will be send to the Rocrail server will show up in the Route Table. With Cancel the recorded route will be rejected.\\ | ||
| + | \\ | ||
| + | **Notes:** | ||
| + | * //Works with Standard and with Staging Blocks.// | ||
| + | * //Steps 5 and 6 may be mixed.// | ||
| + | * //The generated route ID is formatted as: **[from block ID+/-]-[to block ID+/-]**// | ||
| + | * //Pause lines will be ignored.// | ||
| + | * //If some switches and/or signals were left clicked the correct commands can be adjusted in the Route Dialog.// | ||
| + | |||
| + | \\ | ||
| + | |||
| + | =====File format===== | ||
| + | <code> | ||
| + | type,<id>,<cmd> | ||
| + | </code> | ||
| + | Only linefeeds are allowed; No extra carriage return. (DOS/Windows)\\ | ||
| + | "Pause" is not a command but is used to wait for the number of seconds between the playback steps.\\ | ||
| + | |||
| + | ====Example==== | ||
| + | <code> | ||
| + | fb,fb3a,true | ||
| + | pause,2 | ||
| + | fb,fb3b,true | ||
| + | pause,2 | ||
| + | sw,sw2,flip | ||
| + | </code> | ||
rocview/cmdrecorder-en.txt ยท Last modified: 2018/11/12 08:56 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
