User Tools
signal-int-en
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
signal-int-en [2020/01/31 11:42] rjversluis [Aspect numbers] |
signal-int-en [2021/10/26 21:50] rjversluis [Aspect numbers] |
||
|---|---|---|---|
| Line 39: | Line 39: | ||
| * LEDii | * LEDii | ||
| * WIO (WIP) | * WIO (WIP) | ||
| - | \\ | + | |
| + | ====Parameter==== | ||
| + | Special settings for some Command Stations: | ||
| + | * **[[:dccpp:dccpp-en#options1|DCC++]]** | ||
| + | \\ | ||
| ===== Control ===== | ===== Control ===== | ||
| Line 46: | Line 50: | ||
| ==== Patterns ==== | ==== Patterns ==== | ||
| - | Signal decoders are most likely controlled with patterns on two ports. The patterns are set up on the **__[[signal-props-en#patterns|Details]]__** tab.\\ | + | Signal decoders are most likely controlled with patterns on two or three ports. The patterns are set up on the **__[[signal-props-en#patterns|Details]]__** tab.\\ |
| - | See __**[[:signal-setup-en|Signal Setup]]**__, chapter 3.2 for details and examples.\\ | + | See __**[[:signal-setup-en|Signal Setup]]**__, chapter 3.2 for details and examples.\\ |
| + | **Note:** Patterns can only be used with PADA/MADA addressing, and max. 5 aspects. (2.1.601+) __FADA is not supported.__\\ | ||
| ==== Aspect numbers ==== | ==== Aspect numbers ==== | ||
| Line 53: | Line 59: | ||
| The following Command Stations are supported: | The following Command Stations are supported: | ||
| * [[:rocnet:rocnetnode-en|RocNet]] | * [[:rocnet:rocnetnode-en|RocNet]] | ||
| - | * [[:arduino:wio-overview-en|WIO]] | + | * [[:arduino:wio-overview-en|WIOesp/WIOpi/WIOpico]] |
| - | * [[:opendcc-en|OpenDCC Z1]]¹ | + | * [[:opendcc-en|OpenDCC Z1]] |
| * [[:bidib-en|BiDiB]] LightControl | * [[:bidib-en|BiDiB]] LightControl | ||
| - | * [[:sprog-en|SPROG]]¹ | + | * [[:sprog-en|SPROG]] |
| * [[:dinamo-om32-en|OM32]] | * [[:dinamo-om32-en|OM32]] | ||
| * [[:cs2:cs2-en|MCS2]] | * [[:cs2:cs2-en|MCS2]] | ||
| * [[:mbus:cs3-en|MBUS CS2/CS3]] | * [[:mbus:cs3-en|MBUS CS2/CS3]] | ||
| * [[:p50x-tams-en|Tams MC&RB]] | * [[:p50x-tams-en|Tams MC&RB]] | ||
| + | * [[:dccpp:dccpp-en|DCC++/DCCex]] | ||
| | | ||
| - | ¹) [[http://www.nmra.org/standards/DCC/standards_rps/rp921.html#Extended|extended DCC accessory]] | + | |
| ==== Linear ==== | ==== Linear ==== | ||
| Uses only the first address as offset to control all aspects. (Only for FADA/PADA)\\ | Uses only the first address as offset to control all aspects. (Only for FADA/PADA)\\ | ||
signal-int-en.txt · Last modified: 2022/01/29 16:39 by smitt48
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
