This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
signal-int-en [2020/04/03 10:52] rjversluis [Patterns] |
signal-int-en [2021/12/12 17:48] rjversluis [Protocol] |
||
---|---|---|---|
Line 31: | Line 31: | ||
====Protocol==== | ====Protocol==== | ||
- | This is control system dependent. Used only for __**[[:srcp-en|SRCP]]**__, __**[[:ddx-en|DDX]]**__, __**[[:dinamo-en|Dinamo]]**__ and __**[[:opendcc-en|OpenDCC]]**__, otherwise it should be left blank. \\ | + | This is control system dependent. Used only for __**[[:srcp-en|SRCP]]**__, __**[[:dinamo-en|Dinamo]]**__ and __**[[:opendcc-en|OpenDCC]]**__, otherwise it should be left blank. \\ |
====Dim==== | ====Dim==== | ||
Dimming speed for LED type signals.\\ | Dimming speed for LED type signals.\\ | ||
Line 39: | Line 39: | ||
* LEDii | * LEDii | ||
* WIO (WIP) | * WIO (WIP) | ||
- | \\ | + | |
+ | ====Parameter==== | ||
+ | Special settings for some Command Stations: | ||
+ | * **[[:dccpp:dccpp-en#options1|DCC++]]** | ||
+ | \\ | ||
===== Control ===== | ===== Control ===== | ||
Line 46: | Line 50: | ||
==== Patterns ==== | ==== Patterns ==== | ||
- | Signal decoders are most likely controlled with patterns on two ports. The patterns are set up on the **__[[signal-props-en#patterns|Details]]__** tab.\\ | + | Signal decoders are most likely controlled with patterns on two or three ports. The patterns are set up on the **__[[signal-props-en#patterns|Details]]__** tab.\\ |
See __**[[:signal-setup-en|Signal Setup]]**__, chapter 3.2 for details and examples.\\ | See __**[[:signal-setup-en|Signal Setup]]**__, chapter 3.2 for details and examples.\\ | ||
- | **Note:** Patterns can only be used with MADA addressing.\\ | + | **Note:** Patterns can only be used with PADA/MADA addressing, and max. 5 aspects. (2.1.601+) __FADA is not supported.__\\ |
Line 55: | Line 59: | ||
The following Command Stations are supported: | The following Command Stations are supported: | ||
* [[:rocnet:rocnetnode-en|RocNet]] | * [[:rocnet:rocnetnode-en|RocNet]] | ||
- | * [[:arduino:wio-overview-en|WIO]] | + | * [[:arduino:wio-overview-en|WIOesp/WIOpi/WIOpico]] |
- | * [[:opendcc-en|OpenDCC Z1]]¹ | + | * [[:opendcc-en|OpenDCC Z1]] |
* [[:bidib-en|BiDiB]] LightControl | * [[:bidib-en|BiDiB]] LightControl | ||
- | * [[:sprog-en|SPROG]]¹ | + | * [[:sprog-en|SPROG]] |
* [[:dinamo-om32-en|OM32]] | * [[:dinamo-om32-en|OM32]] | ||
* [[:cs2:cs2-en|MCS2]] | * [[:cs2:cs2-en|MCS2]] | ||
* [[:mbus:cs3-en|MBUS CS2/CS3]] | * [[:mbus:cs3-en|MBUS CS2/CS3]] | ||
* [[:p50x-tams-en|Tams MC&RB]] | * [[:p50x-tams-en|Tams MC&RB]] | ||
+ | * [[:dccpp:dccpp-en|DCC++/DCCex]] | ||
| | ||
- | ¹) [[http://www.nmra.org/standards/DCC/standards_rps/rp921.html#Extended|extended DCC accessory]] | + | |
==== Linear ==== | ==== Linear ==== | ||
Uses only the first address as offset to control all aspects. (Only for FADA/PADA)\\ | Uses only the first address as offset to control all aspects. (Only for FADA/PADA)\\ |