Innovative Model Railroad Control System

User Tools

Site Tools

Trace:
signal-int-en

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Next revisionBoth sides next revision
signal-int-en [2020/04/04 08:19] – [Patterns] rjversluissignal-int-en [2021/12/12 17:48] – [Protocol] rjversluis
Line 31: Line 31:
  
 ====Protocol==== ====Protocol====
-This is control system dependent. Used only for __**[[:srcp-en|SRCP]]**__, __**[[:ddx-en|DDX]]**__, __**[[:dinamo-en|Dinamo]]**__ and __**[[:opendcc-en|OpenDCC]]**__, otherwise it should be left blank. \\+This is control system dependent. Used only for __**[[:srcp-en|SRCP]]**__, __**[[:dinamo-en|Dinamo]]**__ and __**[[:opendcc-en|OpenDCC]]**__, otherwise it should be left blank. \\
 ====Dim==== ====Dim====
 Dimming speed for LED type signals.\\ Dimming speed for LED type signals.\\
Line 39: Line 39:
   * LEDii   * LEDii
   * WIO (WIP)   * WIO (WIP)
- \\+ 
 +====Parameter==== 
 +Special settings for some Command Stations: 
 +  * **[[:dccpp:dccpp-en#options1|DCC++]]** 
 +\\
  
 ===== Control ===== ===== Control =====
Line 48: Line 52:
 Signal decoders are most likely controlled with patterns on two or three ports. The patterns are set up on the **__[[signal-props-en#patterns|Details]]__** tab.\\ Signal decoders are most likely controlled with patterns on two or three ports. The patterns are set up on the **__[[signal-props-en#patterns|Details]]__** tab.\\
 See __**[[:signal-setup-en|Signal Setup]]**__, chapter 3.2 for details and examples.\\ See __**[[:signal-setup-en|Signal Setup]]**__, chapter 3.2 for details and examples.\\
-**Note:** Patterns can only be used with MADA addressing, and max. 5 aspects.\\+**Note:** Patterns can only be used with PADA/MADA addressing, and max. 5 aspects. (2.1.601+) __FADA is not supported.__\\
  
  
Line 55: Line 59:
 The following Command Stations are supported: The following Command Stations are supported:
   * [[:rocnet:rocnetnode-en|RocNet]]   * [[:rocnet:rocnetnode-en|RocNet]]
-  * [[:arduino:wio-overview-en|WIO]] +  * [[:arduino:wio-overview-en|WIOesp/WIOpi/WIOpico]] 
-  * [[:opendcc-en|OpenDCC Z1]]¹+  * [[:opendcc-en|OpenDCC Z1]]
   * [[:bidib-en|BiDiB]] LightControl   * [[:bidib-en|BiDiB]] LightControl
-  * [[:sprog-en|SPROG]]¹+  * [[:sprog-en|SPROG]]
   * [[:dinamo-om32-en|OM32]]   * [[:dinamo-om32-en|OM32]]
   * [[:cs2:cs2-en|MCS2]]   * [[:cs2:cs2-en|MCS2]]
   * [[:mbus:cs3-en|MBUS CS2/CS3]]   * [[:mbus:cs3-en|MBUS CS2/CS3]]
   * [[:p50x-tams-en|Tams MC&RB]]   * [[:p50x-tams-en|Tams MC&RB]]
 +  * [[:dccpp:dccpp-en|DCC++/DCCex]]
      
-¹) [[http://www.nmra.org/standards/DCC/standards_rps/rp921.html#Extended|extended DCC accessory]]+
 ==== Linear ==== ==== Linear ====
 Uses only the first address as offset to control all aspects. (Only for FADA/PADA)\\ Uses only the first address as offset to control all aspects. (Only for FADA/PADA)\\
signal-int-en.txt · Last modified: 2023/09/12 08:11 by rjversluis