User Tools

Site Tools


signal-int-en

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
signal-int-en [2020/04/03 10:52]
rjversluis [Patterns]
signal-int-en [2021/12/12 17:48] (current)
rjversluis [Protocol]
Line 31: Line 31:
  
 ====Protocol==== ====Protocol====
-This is control system dependent. Used only for __**[[:​srcp-en|SRCP]]**__, __**[[:​ddx-en|DDX]]**__, __**[[:​dinamo-en|Dinamo]]**__ and __**[[:​opendcc-en|OpenDCC]]**__,​ otherwise it should be left blank. \\+This is control system dependent. Used only for __**[[:​srcp-en|SRCP]]**__,​ __**[[:​dinamo-en|Dinamo]]**__ and __**[[:​opendcc-en|OpenDCC]]**__,​ otherwise it should be left blank. \\
 ====Dim==== ====Dim====
 Dimming speed for LED type signals.\\ Dimming speed for LED type signals.\\
Line 39: Line 39:
   * LEDii   * LEDii
   * WIO (WIP)   * WIO (WIP)
- \\+ 
 +====Parameter==== 
 +Special settings for some Command Stations: 
 +  * **[[:​dccpp:​dccpp-en#​options1|DCC++]]** 
 +\\
  
 ===== Control ===== ===== Control =====
Line 46: Line 50:
  
 ==== Patterns ==== ==== Patterns ====
-Signal decoders are most likely controlled with patterns on two ports. The patterns are set up on the **__[[signal-props-en#​patterns|Details]]__** tab.\\+Signal decoders are most likely controlled with patterns on two or three ports. The patterns are set up on the **__[[signal-props-en#​patterns|Details]]__** tab.\\
 See __**[[:​signal-setup-en|Signal Setup]]**__,​ chapter 3.2 for details and examples.\\ See __**[[:​signal-setup-en|Signal Setup]]**__,​ chapter 3.2 for details and examples.\\
-**Note:** Patterns can only be used with MADA addressing.\\+**Note:** Patterns can only be used with PADA/MADA addressing, and max5 aspects. (2.1.601+) __FADA is not supported.__\\
  
  
Line 55: Line 59:
 The following Command Stations are supported: The following Command Stations are supported:
   * [[:​rocnet:​rocnetnode-en|RocNet]]   * [[:​rocnet:​rocnetnode-en|RocNet]]
-  * [[:​arduino:​wio-overview-en|WIO]] +  * [[:​arduino:​wio-overview-en|WIOesp/​WIOpi/​WIOpico]] 
-  * [[:​opendcc-en|OpenDCC Z1]]¹+  * [[:​opendcc-en|OpenDCC Z1]]
   * [[:​bidib-en|BiDiB]] LightControl   * [[:​bidib-en|BiDiB]] LightControl
-  * [[:​sprog-en|SPROG]]¹+  * [[:​sprog-en|SPROG]]
   * [[:​dinamo-om32-en|OM32]]   * [[:​dinamo-om32-en|OM32]]
   * [[:​cs2:​cs2-en|MCS2]]   * [[:​cs2:​cs2-en|MCS2]]
   * [[:​mbus:​cs3-en|MBUS CS2/CS3]]   * [[:​mbus:​cs3-en|MBUS CS2/CS3]]
   * [[:​p50x-tams-en|Tams MC&RB]]   * [[:​p50x-tams-en|Tams MC&RB]]
 +  * [[:​dccpp:​dccpp-en|DCC++/​DCCex]]
   ​   ​
-¹) [[http://​www.nmra.org/​standards/​DCC/​standards_rps/​rp921.html#​Extended|extended DCC accessory]]+
 ==== Linear ==== ==== Linear ====
 Uses only the first address as offset to control all aspects. (Only for FADA/​PADA)\\ Uses only the first address as offset to control all aspects. (Only for FADA/​PADA)\\
signal-int-en.1585903979.txt.gz · Last modified: 2020/04/03 10:52 by rjversluis