User Tools

Site Tools


stageblock:stage-details-en

Differences

This shows you the differences between two versions of the page.


stageblock:stage-details-en [2025/03/09 09:35] (current) – created - external edit 127.0.0.1
Line 1: Line 1:
 +======Staging Block Details ======
 +[[:english#objects|{{  :objects.png}}]][[:english|{{  :rocrail-logo-35.png}}]]
 +[[:english|Content]] -> [[:english#objects|Objects]] -> **[[:stage-en|Staging Block]]**
 +  * [[:stageblock:stage-index-en|Index]] | [[:stageblock:stage-gen-en|General]] | [[:stageblock:stage-sections-en|Sections]] | **[[:stageblock:stage-details-en|Details]]** | [[:stageblock:stage-perm-en|Permissions]]
 + \\
 +
 + \\
 +===== Details =====
 +These settings are except for the Arrive speed only for the last section where the train starts running in auto mode again.\\
 +{{:stageblock:stageblock-details-en.png?800}}\\
 +See **[[:block-details-en|Block Details]]** for a description of all settings.\\
 +====Minimal occupied====
 +===Trains===
 +The train in the last section may only depart if the number of trains in this staging block is more or equal to this number.\\
 +===Sections===
 +The second field is the number of sections which must be __electrically occupied__ before the first train is allowed to leave.\\
 +
 + \\
 +====Best choice====
 +This option will help to get trains choosing this staging block instead of other blocks.\\ 
 +A random choice will happen if more than one available block to choose from has this option.\\
 +
 +====In event at train length====
 +Generate the **in** event if the train completely fits in the staging block instead of reaching the destination section to free up the previous block.\\
 +**Note:** //With this option active the wait time will be ignored if no other locomotives are in the stage block.//\\
 +
 +
 +====Electrified====
 +This option can be activated for staging blocks equipped with a catenary. \\
 +If NOT set this prevents locos with **engine type electric** (see **[[:loc-details-en|Locomotive Details]]**) from using this staging block in auto mode.
 +
 +====Watchdog====
 +Checks every x seconds if auto mode is enabled and if the head section is free and one or more trains are in the staging block to trigger compression.\\
 +Compression is normally triggered by sensor events and lock/unlock commands, but under certain conditions this is not possible and in this case the watchdog will trigger it.\\
 +The check interval in seconds can be set in the field at the right side of this option.\\
 +===Timeout===
 +Pending compression timeout in seconds if set greater then zero.\\
 +
 + \\
 +=====Wait=====
 +====Type====
 +The wait type for the locomotive in the last section.\\
 +Avoid using **None** or a very short wait time, in combination with a manual operated exit signal to prevent unnecessary data traffic.\\
 + \\
 +
 +=====Speed=====
 +====Arrive====
 +The minimal speed is default and should be used if the sections are relative short.\\
 +Both other speed options can be used, as the initial arriving speed, if there is enough room behind the section sensor to decelerate from Vmid to V0; Use with care.\\
 +:!: **Please note:** Between the sections, the train always advances with the Arrive speed (Vmin, Vmid or %). \\
 +Into the last section of an Compress action and into the last section of the Staging block, a train always drives with Vmin.\\
 +
 +Numerical selection is used by speed selection of %. \\
 +
 +===Use arrive speed to target section===
 +This option __overrules__ the Vmin to the last section of an Compress action and into the last section of the Staging block, and uses the arrive speed.\\
 +===Vmin to first section===
 +Lok advances with Vmin to the end of the first section, if the subsequent sections are occupied.
 +\\
 +====Depart====
 +The depart speed of the locomotive in the last section.
 +
 + \\
 +
 +===== Commands (Right mouse click)=====
 +
 +==== Compress (move up)====
 +  * Advance the occupying trains with the selected Arrive speed (Vmin, Vmid or %) towards the end section, to fill up gaps and make room at the start.
 +  * Turn on the auto mode of the train waiting in the end section if the exit state is open.
 +
 +==== Close/Open exit ====
 +Controls the output flow, exit, of the staging block.\\
 +
 +==== In/Out of Operation ====
 +Controls the input flow, enter, of the staging block.\\