switch-int-en
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
switch-int-en [2019/04/04 00:29] – [Multiple switches at the same decoder output] rainerk | switch-int-en [2023/10/19 12:23] (current) – rjversluis | ||
---|---|---|---|
Line 3: | Line 3: | ||
[[english|Content]] -> [[english# | [[english|Content]] -> [[english# | ||
- | * [[switch-index-en|Index]] | [[switch-gen-en|General]] | **[[switch-int-en|Interface]]** | [[switch-wiring-en|Wiring]] | [[switch-ctrl-en|Control]] | [[switch-frog-en|Frog]] | [[switch-td-en|Trackdriver]] | [[switch-usage-en|Usage]] | + | * [[switch-index-en|Index]] | [[switch-gen-en|General]] | **[[switch-int-en|Interface]]** | [[switch-wiring-en|Wiring]] | [[switch-ctrl-en|Control]] | [[switch-frog-en|Frog]] | [[switch-td-en|Trackdriver]] | [[switch-usage-en|Usage]] | [[switch-menu-en|Menu]] |
// \\ // \\ | // \\ // \\ | ||
Line 9: | Line 9: | ||
Switch Dialog Interface Tab.\\ | Switch Dialog Interface Tab.\\ | ||
- | {{: | + | {{: |
\\ | \\ | ||
=====Interface ID===== | =====Interface ID===== | ||
- | If more than one Command Station (CS) is defined in Rocrail __and__ | + | If more than one command station |
- | + | ||
- | \\ | + | |
=====Bus===== | =====Bus===== | ||
See: **[[: | See: **[[: | ||
Line 44: | Line 41: | ||
* **[[: | * **[[: | ||
* **[[: | * **[[: | ||
- | * DCC++ IFLAG | + | * **[[: |
Line 78: | Line 75: | ||
=====Switch time===== | =====Switch time===== | ||
+ | :!: Activate this timer in case the motor does not switch itself off!\\ | ||
Some Command Stations allow to define a switch activation time. Check your manual for details. | Some Command Stations allow to define a switch activation time. Check your manual for details. | ||
The time here is in ms.\\ | The time here is in ms.\\ | ||
+ | | Tip: It is much safer to define coil power off in the decoder instead of relying on a second command which could be missed by the decoder and overheat the coil. | | ||
====Synchronise==== | ====Synchronise==== | ||
Line 113: | Line 112: | ||
>Then the establishment of actions and the virtual CS is not required. \\ | >Then the establishment of actions and the virtual CS is not required. \\ | ||
For **manual** switches you can choose an address of 0 on your default controller. However, if you like to see the switch move on the screen, then you can use the virtual controller. In either case no commands are sent to the controller. | For **manual** switches you can choose an address of 0 on your default controller. However, if you like to see the switch move on the screen, then you can use the virtual controller. In either case no commands are sent to the controller. | ||
- | |||
\\ | \\ | ||
+ | --></ | ||
Partial list of CS that will work with multiple switches on the same decoder output | Partial list of CS that will work with multiple switches on the same decoder output | ||
- | | + | |
+ | |||
Partial list of CS that will **not** work with multiple switches on the same decoder output | Partial list of CS that will **not** work with multiple switches on the same decoder output | ||
- | | + | |
- | --></ | + | |
\\ | \\ | ||
+ | =====Parameter===== | ||
+ | Parameter is used to affect servo bouncing in the **[[wio: | ||
+ | |||
+ | |||
+ | \\ | ||
+ | =====3W OneServo===== | ||
+ | Using just one servo for a 3W is very common for car systems.\\ | ||
+ | |||
+ | Setup by setting the Address an Port for both motors the same, and select Type Servo.\\ | ||
+ | |||
+ | |< >| | ||
+ | ^ Position ^ Field ^ Remark ^ | ||
+ | | Right | Param 1 | | ||
+ | | Straight | Value 1 | If zero the value will be calculated. | | ||
+ | | Left | Param 2 | | ||
+ | |||
+ | |||
+ | |||
+ | |||
switch-int-en.1554330584.txt.gz · Last modified: 2019/04/04 00:29 by rainerk