no way to compare when less than two revisions

Differences

This shows you the differences between two versions of the page.

@@ Line 1: / Line 1: @@
+======Connect to======
+{{  rocrail-logo-32.png}}
+[[english|Content]] -> [[english#rocview|Rocview]]->[[english#general|General]]
+  *  [[rocgui-config-en|Configuration]] | [[loc-tab-en|Locomotives Tab]] | [[gui-accel-en|Accelerators]] | [[gui-cs-status-en|Command Station Status]] | [[gui-multi-en|Use multiple Gui's for viewing]] | [[gui-reports-en|Reports]] | **Connect to**
+ \\
+If the Rocrail server runs on another computer than **localhost**, you can connect to it by this option if no workspace has been opened:\\
+{{rocgui-connectto-en.png}}\\
+ \\
+This dialog is found in the File menu:\\
+**File** -> **Connect to...**\\
+ \\
+===== Hostname =====
+The "Help/Info" dialogue of Rocview will show you the IP adress.
+Another way to determine the hostname or IP address:
+==== Windows ====
+Open a command window and issue the **ipconfig** command:
+<code>
+> ipconfig
+Windows-IP-Konfiguration
+Ethernetadapter LAN-Verbindung 2:
+        Verbindungsspezifisches DNS-Suffix: siworld.local
+        IP-Adresse. . . . . . . . . . . . : 10.0.2.15
+        Subnetzmaske. . . . . . . . . . . : 255.255.255.0
+        Standardgateway . . . . . . . . . : 10.0.2.2
+</code>
+ \\
+In this example **10.0.2.15** is the Hostname to use in the Rocview dialog.
+==== Linux / OS X ====
+<code>
+$ /sbin/ifconfig
+eth0      Link encap:Ethernet  HWaddr 00:13:72:a9:03:cf
+          inet addr:192.168.200.201  Bcast:192.168.200.255  Mask:255.255.255.0
+          inet6 addr: fe80::213:72ff:fea9:3cf/64 Scope:Link
+          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
+          RX packets:17641 errors:0 dropped:0 overruns:0 frame:0
+          TX packets:11904 errors:0 dropped:0 overruns:0 carrier:0
+          collisions:0 txqueuelen:1000
+          RX bytes:13797015 (13.7 MB)  TX bytes:1903395 (1.9 MB)
+          Interrupt:16
+</code>
+ \\
+In this example **192.168.200.201** is the Hostname to use in the Rocview dialog.
+ \\
+===== Port =====
+The standard default client service port is 8051.\\
+Check the **[[rocrailini-service-en#client_service|Client Service]]** of the Rocrail server for the correct port.\\
+ \\
+===== R2RNet =====
+A list of Rocrail Servers found in the network if R2RNet is activated in Rocview and Servers.\\
+See __**[[:rocgui-gen-en#r2rnet|R2RNet]]**__\\
+ \\
+===== Control code =====
+Only needed if the Rocrail server has set a **[[rocrailini-service-en#control_code|control code]]** to get write access.\\
+ \\
+=====Slave code=====
+See: __**[[:rocrailini-service-en#slave_code|Slave code]]**__\\