no way to compare when less than two revisions

Differences

This shows you the differences between two versions of the page.

@@ Line 1: / Line 1: @@
+======MBUS CS2/CS3======
+[[:english#command_stations|{{  :interface.png}}]][[:english|{{  :rocrail-logo-35.png}}]]
+[[:english|Content]] -> **[[:english#command_stations|Command Stations]]** -> Märklin
+  * **[[:mbus:mbus2-en|MBUS]]**
+    * [[:mbus:functions-en|Function Codes]] | **[[:mbus:cs3-en|CS2/CS3]]** |  [[:mbus:mbus-en|TrackBox(GleisBox)]] | [[:mbus:channels-en|Channels]]
+{{:mbus:cs3plus.png?200}}\\
+^  The MCS2 library is replaced by the MBus library.  ^
+^  :!: Only PADA is supported for accessory like switches, signal and outputs! :!:  ^
+=====TCP Communication=====
+^  Note: Only direct TCP communication with the CS2/CS3 is supported in the Rocrail Forum.  ^
+====IP Address====
+The CS3 has [[https://en.wikipedia.org/wiki/Dynamic_Host_Configuration_Protocol|DHCP]] active by default, and will get an IP address from router (In this example a FritzBox.):\\
+|{{:mbus:cs3-ip-de.png?0x240}}|{{:mbus:mbus-cs3-fritz-de.png?0x240}}|\\
+The host name, in this example **CS3-06294**, can be used in Rocrail instead of using the IP address, \\
+====Communication Type====
+The preferred way to communicate with the CS3 is by using the TCP type.\\
+The CS3 TCP port is factory set to 15731, the second port is not utilized.\\
+Classic CS2 UDP communication uses two port numbers, sending (Tx) and receiving (Rx). \\
+If the port entry is set to zero, it is automatically replaced with the default values, 15731 and 15730. \\
+{{:mbus:mbus-interface-en.png}}\\
+====Overview====
+If all went well, the CS3 is listed in the CBUS/MBUS dialog:\\
+{{:mbus:mbus-node-index-en.png}}\\
+Menu: **Rocview -> Programming ->CBUS/MBUS** \\
+ \\
+=====Sensors=====
+====Poll at SoD====
+Use only in case of Gleisreporter de Luxe.\\
+====S88 CS2/CS3plus====
+This setup is needed to be able to detect the sensor state at start up.\\
+|{{:mbus:cs3-plus-s88-de.png?0x240}}|{{:mbus:mbus-sensors-en.png?0x240}}|\\
+Check the CS3 System setup for ID and number of connected modules.\\
+===ID===
+//"Kennung"//((German screen shot))\\
+The S88 Device ID to use for 'Start of Day'.\\
+This ID is also the reported bus value.\\
+===Modules===
+//"Länge S88 Bus"//((German screen shot))\\
+The number of connected 16 port S88 modules.\\
+ \\
+====LinkS88====
+|  //This setup is no longer needed; Its detected automatically.//  |\\
+<del>This setup is needed to be able to detect the sensor state at start up.</del>
+|{{:mbus:links88-setup-de.png?0x240}}|{{:mbus:mbus-sensors-en.png?0x240}}|\\
+An entry in the list is needed for each connected LinkS88 device.\\
+Check the CS3 System setup for ID and number of connected modules.\\
+ \\
+=====Options=====
+{{:mbus:mbus-options-en.png}}\\
+See: __**[[:mbus:mbus-en#report_state|MBUS Options]]**__\\
+====Acknowledge sensor events====
+This option only has effect in case the __**[[:arduino:rcan-en|GC2a]]**__ is used for sensor detecting.\\
+It will only acknowledge the high state of sensor events.\\
+Turn this option off in all other cases.\\
+====Auto switch delay====
+A switch delay time is always send in case this option is active. (Default active)\\
+This is independent of the individual [[:switch-int-en#switch_time|Switch Time]]. The global switch delay is used if the individual switch time is set to zero.\\
+ \\
+=====Switch time=====
+__**[[:switch-int-en#switch_time|Activate this timer in case the motor does not switch itself off!]]**__ \\
+:!: Disabled end contacts will burn the coils of the motor if the switch time is not activated.\\
+ \\
+=====Addressing=====
+====Switch/Output====
+|< >|
+|  :!: **Adress always zero and port 1...n**  |
+An example for the real switch address **12**:
+|< >|
+^ Type ^ Address ^ Port ^ Remark ^
+^ MADA |   3 |   4 | :!: Not supported! |
+^ PADA |   0 |  12 | Same scheme as the display address in the CS2/CS3 GUI. |
+^ FADA |  12 |   - | :!: Not supported! |
+ \\
+=====Loco List/Discover=====
+|< >|
+| **Rocview -> Control -> Discover** |
+The Discover command can be used to get the locos from the CS2/CS3.\\
+New discovered locos during the session are automatically added to Rocrail.\\
+ \\
+=====WEB Service=====
+{{ :mbus:cs3-web-de.png?0x200}}
+The CS3 has a build in WEB service which can be viewed with the following URL:
+<code>
+http://cs3-06294
+</code>
+Where **[[#ip_address|cs3-06294]]** is the host name of the CS3.\\
+The WEB service provides the following facilities:
+  * Help
+  * Setup
+  * App Service
+  * And more...
+ \\