User Tools
blocksideroutes-fr
Differences
This shows you the differences between two versions of the page.
| — |
blocksideroutes-fr [2018/11/12 08:56] (current) |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ======Blocs dans les itinéraires====== | ||
| + | [[:france#automatic mode|{{ :automat.png}}]][[:france|{{ :rocrail-logo-35.png}}]] | ||
| + | [[france|Sommaire]] -> [[france#automatic mode|Mode Automatique]] | ||
| + | * **Blocs dans les itinéraires**\\ | ||
| + | \\ | ||
| + | **TRADUCTION EN COURS** | ||
| + | \\ | ||
| + | \\ | ||
| + | ** Le principe des blocs dans les itinéraires ** | ||
| + | \\ | ||
| + | Autres pages importantes sur le sujet: | ||
| + | * **[[:direction-fr|Direction dans les blocs dans les itinéraires]]** | ||
| + | * **[[:commuter-setup-fr|Configuration d'un train de banlieu]]** | ||
| + | |||
| + | \\ | ||
| + | |||
| + | ===== Introduction ===== | ||
| + | Block side routes offer advantages over the classical routes since undesired direction changes by trains can be eliminated because a logical, clear direction of movement independent of the direction of travel of the locomotive is defined and routes can be used in the declared direction (from - to) only. | ||
| + | |||
| + | Reversing loops are easily achievable with the block side concept since the logical direction of the train after passing through the loop remains unchanged. Thus, there is no need to think about where to a apply a change of directions within the reversing loop. | ||
| + | |||
| + | \\ | ||
| + | ===== Setup ===== | ||
| + | {{ route.jpg}} | ||
| + | The automat uses the ''+''/''-'' side of block to determine the right route for the current travelling direction.\\ | ||
| + | If a train enters a block at the ''+'' side it must leave the block at the ''-'' side to keep the right traveling direction.\\ | ||
| + | {{:icons:plus.png?12}}{{:blockside:blockside.png?150}}{{:icons:minus.png?12}}\\ | ||
| + | The checkboxes right from the **From** and **To** block, in the **[[:route-gen-en|Route general]]** tab, are used to define the route block connection.\\ | ||
| + | {{:blockside:blockside-checkbox.png}}\\ | ||
| + | \\ | ||
| + | Some options, like Run direction, found on the **[[:route-gen-fr|itinéraires général]]** tab are no longer needed for the block side method.\\ | ||
| + | :!: The "Both directions" options should not be used when "Block sides" is activated. Only "From-To" routes are allowed and they **must** be defined with Run direction **"Forwards"**.\\ | ||
| + | \\ | ||
| + | ===== Paramètres ===== | ||
| + | * Placement des Locos | ||
| + | * Côté d'entrée du Bloc; ''+''/''-'' | ||
| + | * Follow up route block exit side; ''+''/''-'' | ||
| + | |||
| + | \\ | ||
| + | ===== Loco enter side flag ===== | ||
| + | The loco enter side flag is saved on shutdown for the right initialization at the next Rocrail session.\\ | ||
| + | This flag can be adjusted with the context menu item "Swap enter side" in the Rocview loco tab.\\ | ||
| + | {{:blockside:blockside-swap.png}}\\ | ||
| + | The value of this flag is shown in the block column; The block ID will be prefixed with a ''-'' if the block enter side was ''-''. (No prefix if the enter side was ''+''.)\\ | ||
| + | {{:blockside:blockside-rocview.png}}\\ | ||
| + | A placing swap will __automatically__ swap the block enter side, but not visa versa.\\ | ||
| + | |||
| + | \\ | ||
| + | ===== Sensor Configuration ===== | ||
| + | Sensors have to be assigned to the routes on the **[[:block-routes-en|routes tab]]** found in the block properties. The sensors are assigned to the routes __all__ and __all-reverse__, respectively. The __all__ route is for all routes heading towards the ''+'' side of the block (marked with the little ''+'' in SpDrS60 theme). The __all-reverse__ route accordingly in used for all routes heading towards the ''-'' side of the block. | ||
| + | |||
| + | \\ | ||
| + | ===== Block Route events ===== | ||
| + | __**[[:block-routes-en#specific_and_unspecific_routes|Block Routes]]**__ | ||
| + | |||
| + | |||
| + | |||
| + | \\ | ||
| + | ===== Reverse Loop Example ===== | ||
| + | {{:blockside:blockside-example.png?900}}\\ | ||
| + | Place the locomotive in block **D** and make sure the enter block side flag is ''+''.\ | ||
| + | Switch on the auto mode and start the locomotive.\\ | ||
| + | It will travel always in the following sequence:\\ | ||
| + | D -> C -> A -> B -> C -> D \\ or \\ D -> C -> B -> A -> C -> D\\ | ||
| + | \\ | ||
| + | ==== Routes ==== | ||
| + | ^ ID ^ From ^ To ^ Valid train enter flag ^ | ||
| + | | DC | -D | +C | initial start or swapped after CD to ''+'' | | ||
| + | | CA | -C | +A | entered at ''+'' in C | | ||
| + | | AB | -A | -B | entered at ''+'' in A | | ||
| + | | BC | +B | -C | entered at ''-'' in B | | ||
| + | |||
| + | \\ | ||
| + | ==== Files ==== | ||
| + | * {{:blockside:plan.xml}} | ||
blocksideroutes-fr.txt · Last modified: 2018/11/12 08:56 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
