User Tools

Site Tools


dinamo-om32-en

Differences

This shows you the differences between two versions of the page.


dinamo-om32-en [2024/11/30 07:24] (current) – created - external edit 127.0.0.1
Line 1: Line 1:
 +======Dinamo OM32/OC32/PM32======
 +[[:english#command_stations|{{  :interface.png}}]][[:english|{{  :rocrail-logo-35.png}}]]
 +[[:english|Content]] -> [[:english#command_stations|Command Stations]] ->  **Dinamo**
 +  *  [[:dinamo-en|RM-H, RM-U]] | **[[:dinamo-om32-en|OM32/OC32/PM32]]** | [[:dinamo-car-en|MCC Car System]]
 + \\
 +| {{http://www.vpeb.nl/files/1613/0627/7263/OM32.jpg?300}} | {{http://www.vpeb.nl/files/cache/1486e5a57cdfa9916a941cab39ada8ba_f40.jpg?250}} | {{http://www.vpeb.nl/files/cache/4da4709021baca1c4749c09c2494abe9_f41.jpg?0x200}}|
 +|  [[http://www.vpeb.nl/oplossingen/accessoires/om32-serial/|OM32]]((Der OM32 wird nicht mehr hergestellt.))  |  [[http://www.vpeb.nl/oplossingen/accessoires/oc32/|OC32]]((Der OC32 ist der Nachfolger des OM32.))  |  [[http://www.vpeb.nl/oplossingen/treinen/pm32/|PM32]]  |
 +
 + \\
 +=====RM-H/U=====
 +Library: **[[:dinamo-en|dinamo]]**\\
 +Indirectly controlled by the Dinamo interface.
 +  * Switches/Outputs -> OM32 protocol
 +  * Switches/Outputs as Digital Output -> DO protocol
 +  * Switches/Outputs as Virtual Output -> VO protocol
 +  * Switches/Outputs as Default -> PM32 protocol
 +  * Signals -> Aspects only
 +
 + \\
 +
 +=====RS485=====
 +[[http://www.vpeb.nl/producten/actuele-producten/oc32/u485/|{{ http://www.vpeb.nl/files/3013/0607/6054/u485.jpg?150}}]]
 +Library: **om32**\\
 +Baudrate: 9.600, 19.200 or 38.400((The OC32 module is auto-baud. This means it determines the correct bitrate from the received datastream. In order to minimize start-up errors the initial (start-up) bitrate can be configured by the user.))\\
 +Directly controlled by a separate RS485 connection.\\
 + \\
 +
 +====Addressing====
 +| Field ^ Value ^ Range ^
 +^ Address | OM32 module number + 1 | 1...8 |
 +^ Port    | OM32 output number + 1 | 1...32 |
 +
 + \\
 +==== Switches ====
 +| |  Type  ||||
 +^ Field ^ Motor ^ Servo ^ Lights ^
 +| **[[:switch-int-en#parameter_value|Param]]** | PWM straight (0...31)  | Position straight (0...127)  | Aspect (0...12) straight |
 +| **[[:switch-int-en#parameter_value|Value]]**  | PWM turnout (0...31)   | Position turnout (0...127) | Aspect (0...12) turnout |\\
 +
 +  * Uncheck the __**[[:switch-int-en#accessory|Accessory]]**__ option for selecting the wanted port type.
 +  * Check the __**[[:switch-int-en#single_gate|Single Gate]]**__ option if only __one output__ should be addressed, otherwise the next output is used for the **turnout** command. (Dual coil)
 + \\
 +
 +====Signals====
 +  * __**[[:signal-int-en#aspect_numbers|Aspects]]**__(OC32)
 +  * {{:dinamo:oc32_signals.pdf}} (User document for UK signals.)
 +
 + \\
 +
 +====Outputs====
 +| |  Type  ||||
 +^ Field ^ Accessory ^ Motor ^ Servo ^ Lights ^
 +| **[[:output-int-en#parameter|Param]]** | Gain  | PWM OFF (0...31)  | Position OFF (0...127)  | Aspect (0...12) OFF |
 +| **[[:output-int-en#value|Value]]**  | 1   | PWM ON (0...31)   | Position ON (0...127) | Aspect (0...12) ON |\\
 +
 +  * Uncheck the accessory option for selecting the wanted port type.
 +  * The __**[[:output-int-en#blink|Blink]]**__ option is available for the accessory port type only.
 +
 +
 + \\
 +
 +====Configuration Tools====
 +  * [[http://www.vpeb.nl/english/support/oc32-toolkit|Toolkit OC32]]
 +
 +
 + \\
 +