gca:wioprog2-en
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
gca:wioprog2-en [2020/11/11 07:50] – [WIO_Prog2 DCC central station with 2 x 3,5 amp output and programming track option.] rjversluis | gca:wioprog2-en [2023/09/25 11:03] (current) – [Jumper settings] phg | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== WIO_Prog2 DCC central station with 2 x 3,5 amp output and programming track option. ====== | ====== WIO_Prog2 DCC central station with 2 x 3,5 amp output and programming track option. ====== | ||
+ | [[english|{{ : | ||
+ | * [[: | ||
+ | * [[: | ||
+ | * [[: | ||
{{ : | {{ : | ||
- | [[english|{{ : | ||
\\ | \\ | ||
Line 11: | Line 14: | ||
* Programming track 1 Amp maximum current | * Programming track 1 Amp maximum current | ||
* Fastled control | * Fastled control | ||
- | * CAN bus | + | * Isolated |
- | * RocNet | + | * WIO |
- | * Standard | + | * I2C bus (standard and RocNet) |
* Rocrail control via WIFI, CAN or USB | * Rocrail control via WIFI, CAN or USB | ||
- | * Standard I2C bus | ||
* Railcom capable with GCA214 detector | * Railcom capable with GCA214 detector | ||
- | * two rail output 3,5 Amp each | + | * two rail outputs each 3,5 Amp (1 Amp in programming mode) |
- | | + | \\ |
+ | \\ | ||
+ | ===== Description ===== | ||
+ | |||
+ | This central station is a follow-up from WIO_Prog1.\\ | ||
+ | Since most central station now are working with a dc power supply, that is needed for this one too.\\ | ||
+ | With two built-in 3, | ||
+ | railroad tracks, both wih their own section.\\ | ||
+ | In that case you are not working with 7 Amp power on the rails, but with two sections with 3,5 Amp each.\\ | ||
+ | The ouput is electronically fused, so short circuit will imediate switch off total power.\\ | ||
+ | WIO_prog2 can be controlled from Rocrail via WIFI, USB and CAN. \\ | ||
+ | The used firmware is the same firmware as for all WIO units, using Lolin D1 or D32 (Arduino related) modules.\\ | ||
+ | \\ | ||
+ | ===== Loco Node-ID==== | ||
+ | DCC Locomotives must be set IID to WIO and Node-ID to the ID of the WIO-Prog2.\\ | ||
+ | |||
+ | |||
+ | \\ | ||
+ | ===== further info ===== | ||
+ | Since this board is using same firmware as other WIO related units, the complete concept\\ | ||
+ | is explained in one page. | ||
+ | [[ https:// | ||
===== Hardware ===== | ===== Hardware ===== | ||
- | ^ **Note | + | | {{ :gca: |
- | | {{ : | + | | {{ : |
- | | {{: | + | | {{: |
+ | | {{ : | ||
+ | \\ | ||
+ | ===== Jumper settings ===== | ||
+ | ^ JP1 ^ Maximum current selector | ||
+ | | 1-2 connected | ||
+ | | 2-3 connected | ||
+ | \\ | ||
+ | ^ JP2 + JP3 ^ IIC pull up for bus driver | ||
+ | | 1-2 connected | ||
+ | | 2+3 connected | ||
+ | \\ | ||
+ | ^ JP4 CAN bus terminator | ||
+ | | set this jumper when CAN bus is used, and this unit is on one end of the CAN line | | ||
+ | \\ | ||
+ | |||
+ |
gca/wioprog2-en.1605077405.txt.gz · Last modified: 2020/11/11 07:50 by rjversluis