Differences

This shows you the differences between two versions of the page.

--- mbus:cs3-en [2020/12/02 18:50] – [CS2 / CS3] besra
+++ mbus:cs3-en [2022/05/01 10:40] (current) – [Switch/Output] rjversluis
@@ Line 2: / Line 2: @@
 [[:english#command_stations|{{  :interface.png}}]][[:english|{{  :rocrail-logo-35.png}}]]
 [[:english|Content]] -> **[[:english#command_stations|Command Stations]]** -> Märklin
-  * **[[:mbus:mbus-en|MBUS]]**
+  * **[[:mbus:mbus2-en|MBUS]]**
     * [[:mbus:functions-en|Function Codes]] | **[[:mbus:cs3-en|CS2/CS3]]** |  [[:mbus:mbus-en|TrackBox(GleisBox)]] | [[:mbus:channels-en|Channels]]
 {{:mbus:cs3plus.png?200}}\\
@@ Line 16: / Line 16: @@
 ====Communication Type====
 The preferred way to communicate with the CS3 is by using the TCP type.\\
+The CS3 TCP port is factory set to 15731, the second port is not utilized.\\
+Classic CS2 UDP communication uses two port numbers, sending (Tx) and receiving (Rx). \\
+If the port entry is set to zero, it is automatically replaced with the default values, 15731 and 15730. \\
 {{:mbus:mbus-interface-en.png}}\\
-The CS3 TCP port is factory set to 15731.\\
 ====Overview====
 If all went well, the CS3 is listed in the CBUS/MBUS dialog:\\
@@ Line 42: / Line 45: @@
  \\
 ====LinkS88====
-|  //Starting with revision 15.073, this setup is no longer needed; Its detected automatically.//  |\\
+|  //This setup is no longer needed; Its detected automatically.//  |\\
-This setup is needed to be able to detect the sensor state at start up.\\
+<del>This setup is needed to be able to detect the sensor state at start up.</del>
 |{{:mbus:links88-setup-de.png?0x240}}|{{:mbus:mbus-sensors-en.png?0x240}}|\\
 An entry in the list is needed for each connected LinkS88 device.\\
@@ Line 70: / Line 73: @@
 =====Addressing=====
 ====Switch/Output====
-An example for the real switch address **11**:
+An example for the real switch address **12**:
 |< >|
-^ Type ^ Address ^ Port ^ Calculation ^ Remark ^
+^ Type ^ Address ^ Port ^ Remark ^
-^ MADA |   3 |   4 |  (3-1)*4+(4-1)=11 | |
+^ MADA |   3 |   4 | Not supported! |
-^ PADA |   0 |  12 |  12-1=11 | Recommended: Same scheme as the display address in the CS2/CS3 GUI. |
+^ PADA |   0 |  12 | Same scheme as the display address in the CS2/CS3 GUI. |
-^ FADA |   - |  - | Not supported! | |
+^ FADA |   - |   - | Not supported! |
  \\
@@ Line 100: / Line 103: @@
  \\
-===== Connecting a CS2 / CS3 with Rocrail step-by-step =====
-  - Select in the toolbar: File
-  - Select in the menu: Open Workspace / Recent Workspace
-  - Open the desired file
-  - Select in the toolbar: File
-  - Choose in the menu: Rocrail Properties. A new window will open
-  - Select the tab: Controller
-  - Click on the vcs-1 (virtual controller), which is in the window
-  - Click on: delete
-  - Click on dropdown: new
-  - Select: MBUS and click on it
-  - Click on: add, in the window appears: NEW (the selected MBUS)
-  - Click on: NEW in the window
-  - Click on: Properties
-  - Click on: Interface ID and change the name NEW to a name of personal choice, e.g. ''CS3'' or ''CS-3''
-  - Check: TCP, enter the IP address at Hostname and after the colon 15731
-  - Click on: OK
-  - Close Rocrail (in Win: Ctrl-D, in MacOS: Strg-D)
-  - Restart Rocrail, perform Steps 1, 2 en 3 again
-  - Start the CS3 and put it on stop
-  - Click on the lightbulb icon in the toolbar: the CS3 now switches on
-  - Click on the lightbulb icon in the toolbar: Turn off the power, the CS3 now switches off
-  - Select in the toolbar: Programming
-  - Click in the menu on: CANBUS, a window will open and the window should contain the CS3 and the GFP3
-\\ \\