User Tools
rocnet:sw-servo-setup-en
Differences
This shows you the differences between two versions of the page.
|
rocnet:sw-servo-setup-en [2018/11/12 08:56] |
rocnet:sw-servo-setup-en [2018/11/12 08:56] (current) |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== RocNetNode Servo Switch Setup ====== | ||
| + | [[:english#command_stations|{{ :interface.png}}]][[:english|{{ :rocrail-logo-35.png}}]][[:rocnet:rocnetnode-en|{{ :rocnet:rocnet-hw.png}}]] | ||
| + | [[:english|Content]] -> [[:english#command_stations|Command Stations]] -> **[[rocnet:rocnet-prot-en|RocNet]]** | ||
| + | * [[rocnet:rocnet-prot-en|RocNet Protocol]] | **[[:rocnet:rocnetnode-en|RocNetNode]]** | ||
| + | * [[:rocnet:rocnetnode-hwsetup-en|RocNetNode Setup]] | [[:rocnet:rocnetnode-setup-en|RocNetNode Configuration]] | [[:rocnet:rocnetnode-img-en|Installer package]] | ||
| + | * [[:gca1-pi01-en|GCA-Pi01]] | [[:gca_pi02-en|GCA-Pi02]] | [[:gca-pi03-en|GCA-PI03]] | [[:gca-pi04-en|GCA-PI04]] | [[:gca-pi05-en|GCA-Pi05]] | [[:gca-pi06-en|GCA-Pi06]] | [[:gca107-en|GCA107 Relay board]] | ||
| + | |||
| + | |||
| + | \\ | ||
| + | \\ | ||
| + | =====The example===== | ||
| + | This example shows how to setup a switch controlled by a **[[:rocnet:rocnetnode-en|RocNetNode]]** servo including: | ||
| + | * Interface | ||
| + | * Field feedback (Wiring) | ||
| + | * Frog polarisation. | ||
| + | |||
| + | |||
| + | \\ | ||
| + | |||
| + | =====General===== | ||
| + | {{:rocnet:sw-gen-en.png}}\\ | ||
| + | |||
| + | \\ | ||
| + | =====Interface===== | ||
| + | Set the bus to the RocNetNode-ID, the port type to **Servo** and the address to the channel on which the servo is connected.\\ | ||
| + | {{:rocnet:sw-int-en.png}}\\ | ||
| + | |||
| + | \\ | ||
| + | =====Wiring===== | ||
| + | The **[[:rocnet:rocnetnode-en|RocNetNode]]** wait with generating a 'field event' until the wanted pulse width, position, has been reached.\\ | ||
| + | | Only set **Use field events** for this servo controlled switch. | The __**[[:rocnet:rocnetnode-setup-en#report1|Channel Report]]**__ option must be activated for this functionality. | | ||
| + | | {{:rocnet:sw-wiring-en.png}} | {{:rocnet:sw-channel-setup-en.png}} |\\ | ||
| + | |||
| + | \\ | ||
| + | |||
| + | =====Frog===== | ||
| + | Just set the two relay addresses for frog 1.\\ | ||
| + | These addresses are most likely located on a **[[:gca_pi02-en|GCA-Pi02]]** in combination with a **[[:gca107-en|GCA107]]**.\\ | ||
| + | {{:rocnet:sw-frog-en.png}}\\ | ||
rocnet/sw-servo-setup-en.txt ยท Last modified: 2018/11/12 08:56 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
