no way to compare when less than two revisions

Differences

This shows you the differences between two versions of the page.

@@ Line 1: / Line 1: @@
+======Route Permissions======
+[[:english#objects|{{  :objects.png}}]][[:english|{{  :rocrail-logo-35.png}}]]
+[[:english|Content]] -> [[:english#objects|Objects]] -> **[[:route-en|Routes]]**
+    *  [[:route-index-en|Index]] | [[:route-gen-en|General]] | [[:route-speed-en|Speed]] | [[:route-turnouts-en|Commands]] | [[:route-sensors-en|Sensors]] | **Permission** | [[route-cond-en|Conditions]] | [[route-wiring-en|Wiring]]
+// \\ // \\
+{{route-perm-en.png?801}}
+ \\
+^ :!: Caution in dealing with permissions! Only set when really needed and desired. Failure to correctly set permissions mean that trains do not find a destination and are a recurring theme in the forum.  \\ \\ :!: Set __permissions are always restrictions__ compared to the standard settings. If it is not possible to drive without permissions, setting additional permissions is not a solution, but rather makes the problem worse! ^
+ \\
+=====Description=====
+To prevent certain **[[:loc-index-en|Locomotives]]** and or **[[:operator-consist-en|Trains]]** using a route this tab can be used to define which are permitted or not.\\
+The include list is evaluated first. If empty the exclude list is evaluated.\\
+   - The list "Include" is evaluated with priority. If locomotives or trains are entered here, the route can __only__ be used by these locomotives or trains. \\ Entries in the "Exclude" list are then ignored and for a better overview it is recommended to leave the "Exclude" list empty. \\
+   - The "Exclude" list is only evaluated __if the "Include" list is empty__. Then __only__ locomotives or trains on the "Exclude" list are excluded from using this route. All other locomotives or trains are allowed to use this route.
+> **Note:** Permissions will be respected in **[[:automatic-en#running_without_defined_destination|automatic mode without defined destination]]**. In **[[:automatic-en#running_to_a_defined_destination|automatic mode with defined destination]]**, however, permissions are //not// respected for the destination block and the route to the destination block! Hence, with a given destination it is possible to move a loco or a train into a block by, e.g. drag and drop, although the loco- or train-type is not allowed in this block.
+ \\
+==== Type ====
+Specifies which train types are allowed. All are allowed if no train type is selected.\\
+Further information is found __**[[block_traintype-en|Here]]**__.\\
+ \\
+====Engine====
+Specifies which engine types are allowed. All are allowed if no engine type is selected.\\
+Further information is found __**[[:loc-details-en#engine|Here]]**__.\\
+ \\
+==== Max. train length ====
+If set greater than zero it will be compared with the length of the requesting train.\\
+The route cannot be used when the train length (+ Min Block - Train length) exceeds the max. train length allowed.
+==== Min. train length ====
+If set greater than zero it will be compared with the length of the requesting train.\\
+The route will not permit it to use when the train length is less than the min. length allowed.\\
+====Length====
+Length of the route between IN of the starting block and ENTER of the target block \\
+This length is used for **[[:rocrailini-automode-en#calculate|Realtime Calculation]]** in __**[[:virtual-automatic-en|Virtual Automatic]]**__ only.
+> Note: For virtual timing also the block length have to be set in the **[[:block-gen-en#length_between_enter_and_in|block length]]**
+====Radius====
+This number reflects the smallest radius of a train, locomotive or wagon that can safely operate in this route. \\
+If a train, locomotive or wagon has as minimum radius bigger than the radius in a route, the route won't be taken.\\
+No checking is done, if this field is zero. \\
+==== Commuter trains====
+===Yes===
+Allow commuter trains.\\
+===Only===
+Allow commuter trains only.\\
+:!: This option will reject all normal trains to use this route.\\
+===No===
+Disallow commuter trains.\\
+ \\
+==== Shunting ====
+===Yes===
+Allow locos in **[[loc-shunting-en|shunting mode]]**.\\
+===Only===
+Allow locos in shunting mode only.\\
+:!: This option will reject all normal trains to use this route.\\
+===No===
+Disallow locos in shunting mode.\\
+==== Logical direction ====
+See: __**[[:loc-details-en#reset_logical_direction|Loco Interface]]**__\\
+===Both===
+All logical directions are allowed.\\
+===Default===
+Only the default logical direction is allowed.\\
+===Swapped===
+Only the swapped logical direction is allowed.\\
+ \\
+==== Auto mode ====
+===Both===
+Schedule and random are both allowed.\\
+===Schedule===
+Only trains running a schedule are allowed.\\
+===Random===
+Only trains __without__ running a schedule are allowed.\\
+===No===
+The route will not be used in automatic mode.\\
+ \\
+=====Class=====
+A comma separated list of allowed __**[[:loc-details-en#class|Loco Classes]]**__.\\
+  * This has no effect if left empty.
+  * Can be modified by the Route action **class**.
+ \\
+=====Era=====
+The allowed __**[[:loc-details-en#era|Loco Era]]**__s. All are allowed if no Era is selected.\\