User Tools

Site Tools


gca:wioprog2-en
no way to compare when less than two revisions

Differences

This shows you the differences between two versions of the page.


gca:wioprog2-en [2024/08/07 08:15] (current) – created - external edit 127.0.0.1
Line 1: Line 1:
 +====== WIO_Prog2 DCC central station with 2 x 3,5 amp output and programming track option. ======
 +[[english|{{ :rocrail-logo-35.png}}]]
 +  * [[:hardware-en|GCA Hardware]]
 +    * [[:hardware-en#wio|GCA WIO]]
 +    * [[:wio:firststeps-en|WIO First steps]]
 +
 +{{ :gca:wio_prog2_pict_01.jpg?200|}}
 +
 + \\
 +
 +^Copyright Rob Versluis and Peter Giling^\\
 +\\
 +===== Features =====
 +  * Programming track 1 Amp maximum current
 +  * Fastled control
 +  * Isolated CAN bus
 +  * WIO
 +  * I2C bus (standard and RocNet)
 +  * Rocrail control via WIFI, CAN or USB
 +  * Railcom capable with GCA214 detector
 +  * two rail outputs each 3,5 Amp (1 Amp in programming mode)
 +\\
 +\\
 +===== Description =====
 + 
 +This central station is a follow-up from WIO_Prog1.\\
 +Since most central station now are working with a dc power supply, that is needed for this one too.\\
 +With two built-in 3,5Amp output drivers, one will have a to use these outputs together on your\\
 +railroad tracks, both wih their own section.\\
 +In that case you are not working with 7 Amp power on the rails, but with two sections with 3,5 Amp each.\\
 +The ouput is electronically fused, so short circuit will imediate switch off total power.\\
 +WIO_prog2 can be controlled from Rocrail via WIFI, USB and CAN. \\
 +The used firmware is the same firmware as for all WIO units, using Lolin D1 or D32 (Arduino related) modules.\\
 + \\
 +===== Loco Node-ID====
 +DCC Locomotives must be set IID to WIO and Node-ID to the ID of the WIO-Prog2.\\
 +
 +
 +
 + \\
 +===== further info =====
 +Since this board is using same firmware as other WIO related units, the complete concept\\
 +is explained in one page.
 +[[  https://wiki.rocrail.net/doku.php?id=arduino:wio-en  ]]
 +===== Hardware ===== 
 +|  {{ :gca:wio_prog2_V3_sch.pdf |The schematics }}  |
 +|  {{ :gca:WIO_Prog2_pcb.pdf |part positions on pcb }}  |
 +|  {{ :gca:wio_prfog2_v3_partslist.pdf |bill of materials}}  |
 +|  {{ firmware.zip | Firmware for IC3 (PICSimulator16) (coming up)}}  |
 +\\
 +===== Jumper settings =====
 +^  JP1  ^  Maximum current selector  ^
 +|  1-2 connected  |  short circuit > 3.5 Amp  |
 +|  2-3 connected  |  short circuit > 1 Amp  |
 +\\
 +^  JP2 + JP3  ^  IIC pull up for bus driver  ^
 +|  1-2 connected  |  P82B715 installed  \\  I2C is buffered for longer line (> 1 meter)  |  
 +|  2+3 connected  |  P82B715 not installed  \\  I2C is directly connected to RocNet 
 +\\  
 +^  JP4               CAN bus terminator  ^
 +|  set this jumper when CAN bus is used, and this unit is at one of the ends of the CAN line  |
 +\\
 + 
 +
  
gca/wioprog2-en.txt · Last modified: 2024/08/07 08:15 by 127.0.0.1