rocrailini-router-en
no way to compare when less than two revisions
Differences
This shows you the differences between two versions of the page.
— | rocrailini-router-en [2022/12/16 14:31] (current) – created - external edit 127.0.0.1 | ||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ====== Router / Checker options====== | ||
+ | [[: | ||
+ | [[:english | Content ]] -> [[: | ||
+ | * [[router-en|Router / Checker]] | ||
+ | * **[[rocrailini-router-en|Router / Checker options]]** | ||
+ | \\ | ||
+ | | :!: **Important Note: \\ From rev. 2.1.2736 the tab __" | ||
+ | |||
+ | \\ | ||
+ | =====Description of the dialogs===== | ||
+ | With the call dialogs for router and checker described here, the options can be set and the functions can be started that determine the mode of operation and the individual steps of the routing and the checks for the current session. | ||
+ | |||
+ | The dialogs for the options and the start of the router and checker functions are called up via \\ | ||
+ | * //Menu -> Track plan -> Router...// | ||
+ | * //Menu -> Track plan -> Checker...// | ||
+ | |||
+ | \\ | ||
+ | ===== Notes===== | ||
+ | Rocrail automatically checks the __**[[planhealth-en|Track plan state]]**__ at every start. There are no options for this automatic check.\\ During current session the track plan status can be determined via //Menu -> Track plan -> Checker [[# | ||
+ | |||
+ | Changing the option setting takes effect only during the current session. | ||
+ | |||
+ | \\ | ||
+ | =====Router===== | ||
+ | {{: | ||
+ | ==== Set routeid for all automatic detected routes ==== | ||
+ | Used to indicates the active route by the route representation {{SpDrS60-track-route.png}} | ||
+ | |||
+ | ==== Set blockid for all blocks ==== | ||
+ | Used to set the representation of items to occupied {{SpDrS60-track-occ.png}} \\ | ||
+ | |||
+ | ==== Assign signals to blocks ==== | ||
+ | Assign signals or distant signals to a block (if not already set) \\ | ||
+ | |||
+ | ==== Assign feedbacks to blocks ==== | ||
+ | Assign feedbacks for action " | ||
+ | |||
+ | ==== Reduce speed ==== | ||
+ | Overwrites the default value of this **[[: | ||
+ | |||
+ | \\ | ||
+ | =====Cleanup===== | ||
+ | {{: | ||
+ | ==== Clean routeid of all automatic detected routes ==== | ||
+ | ==== Reset blockid in whole plan ==== | ||
+ | ==== Reset signal assignments in all blocks ==== | ||
+ | ==== Reset feedback assignments in all blocks ==== | ||
+ | In blocks and selection tables remove action " | ||
+ | |||
+ | \\ | ||
+ | =====Checker===== | ||
+ | =====Check plan health...===== | ||
+ | This general plan consistency check does not require selection of options.\\ | ||
+ | The function corresponds to the automatic check of the __**[[planhealth-en|Track plan state]]**__ at Rocrail start. | ||
+ | \\ | ||
+ | =====Extended plan check===== | ||
+ | {{: | ||
+ | ==== Basic checks on all items ==== | ||
+ | Validate z-level definitions/ | ||
+ | \\ | ||
+ | ==== Checks concerning blocks ==== | ||
+ | Sensor/ | ||
+ | \\ | ||
+ | ==== Checks concerning routes ==== | ||
+ | From, to, crossing blocks, usage, run direction; (switch) commands | ||
+ | \\ | ||
+ | ==== Check actions and conditions ==== | ||
+ | Check/ | ||
+ | |||
+ | \\ | ||
+ | =====Extended plan clean===== | ||
+ | {{: | ||
+ | ==== Clean basic problems on all items ==== | ||
+ | Remove/ | ||
+ | \\ | ||
+ | ==== Clean block problems ==== | ||
+ | Remove/ | ||
+ | \\ | ||
+ | ==== Clean route problems ==== | ||
+ | Remove/ | ||
+ | \\ | ||
+ | ==== Clean action and condition problems ==== | ||
+ | Clean/ | ||
+ | |||
+ | \\ | ||
+ | |< >| | ||
+ | | :!: **Attention: | ||
+ | |||
+ | === How to use " | ||
+ | - Save the plan (copy to a save place!) | ||
+ | - Rocview menu: //Track plan -> Checker...// | ||
+ | - Open the 2. tab " | ||
+ | - Start the cleanup with the button " | ||
+ | - After the dialog with a "Ready message" | ||
+ | \\ |
rocrailini-router-en.txt · Last modified: 2022/12/16 14:31 by 127.0.0.1