User Tools

Site Tools


sensor-int-en

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
sensor-int-en [2020/09/18 12:05]
rjversluis [RFID]
sensor-int-en [2021/05/05 01:17] (current)
rainerk [Type]
Line 10: Line 10:
  
 SensorDialog Interface Tab.\\ SensorDialog Interface Tab.\\
-{{:​sensor-int-en.png}}\\+{{:​sensor-int-en.png?500}}\\
  \\  \\
  
Line 28: Line 28:
 The 32bit RFID number printed on the Tags. (Leading zeros can be left out.)\\ The 32bit RFID number printed on the Tags. (Leading zeros can be left out.)\\
 This can be used in combination with __**[[:​arduino:​wio-en#​id-12la|WIO-Drive and an ID-12LA reader]]**__.\\ This can be used in combination with __**[[:​arduino:​wio-en#​id-12la|WIO-Drive and an ID-12LA reader]]**__.\\
 +All other addressing, like Node ID and Address, are ignored if the RFID did match. (But an additional fake address makes it possible to check the plan virtually.)\\
 {{:​wio:​rfid32.jpg?​600}}\\ {{:​wio:​rfid32.jpg?​600}}\\
 +Example of the blue Tag scan:\\
 +{{:​wio:​rfid-index.jpg}} ​
 <​code>​ <​code>​
 OWIO     0885 Mobile 18 [BR218] RFID event [12.0.197.167.148] [12953492] OWIO     0885 Mobile 18 [BR218] RFID event [12.0.197.167.148] [12953492]
 OModel ​  5329 trying to match sensor event: [WIO] id=[12.0.197.167.148] 0:0 uidname=[] state=0 code=BR218 regval=0 info= OModel ​  5329 trying to match sensor event: [WIO] id=[12.0.197.167.148] 0:0 uidname=[] state=0 code=BR218 regval=0 info=
-OFBack ​  0796 fb[s18-] state=OFF code=BR218 dir=0 val=0 count=5 regval[0]=0+OFBack ​  0796 fb[s18-] state=ON code=BR218 dir=0 val=0 count=5 regval[0]=0
 </​code>​ </​code>​
  
Line 77: Line 80:
  
 =====Type===== =====Type=====
-^ Value  ^ Type  ^ Manu ^ Remark ​ ^+|< >| 
 +^ Value  ^ Type  ^ Manufacturer ​^ Remark ​ ^
 | 0 | Current sensors | - | Most commonly used; Can also report bi-directional information;​ Also for Hall Sensors when not used as wheel counters. | | 0 | Current sensors | - | Most commonly used; Can also report bi-directional information;​ Also for Hall Sensors when not used as wheel counters. |
 | 1 | IR Lissy | Uhlenbrock | Can be used with the __**[[:​sensor-gen-en#​timer|Off timer]]**__ to get it unoccupied. | | 1 | IR Lissy | Uhlenbrock | Can be used with the __**[[:​sensor-gen-en#​timer|Off timer]]**__ to get it unoccupied. |
Line 84: Line 88:
 | 4 | RailCom | - | Not used; Same as type=0. | | 4 | RailCom | - | Not used; Same as type=0. |
 | 5 | RFID | MERG, LDT | Not used; Same as type=0. | | 5 | RFID | MERG, LDT | Not used; Same as type=0. |
-| 6 | Wheel counter | **[[:​gca173-en|GCA173 ​Hall Sensors]]**, **[[:​mgv141-en|GCA141]]** | Used for wheel or car counting. |\\+| 6 | Wheel counter | **[[:​gca173-en|GCA173]]**, ​**[[:​gca179-en|GCA179]]** and **[[:​mgv141-en|GCA141]]** ​\\ for Hall sensors and Reed contacts. ​| Used for wheel or car counting. |\\
 | 7 | GPS | **[[:​got:​got-en|GamesOnTrack]]** | Using the GPS coordinates on the GPS tab. | | 7 | GPS | **[[:​got:​got-en|GamesOnTrack]]** | Using the GPS coordinates on the GPS tab. |
-| 8 | Register | - | Can be used for __**[[:​turntable-int-en#​position_sensors|Turntable position sensor]]**__. ​(Selectrix based systems) ​ |+| 8 | Register | - | Can be used for __**[[:​turntable-int-en#​position_sensors|Turntable position sensor]]**__. ​ |
  
 Read **[[sensor-bi-directional-en|Bi-Directional Communication]]** for more information on this topic.\\ Read **[[sensor-bi-directional-en|Bi-Directional Communication]]** for more information on this topic.\\
- 
- 
  \\  \\
 +=====Register trigger===== 
 +Specifies the physical quantity for which the value represented by the register bits is defined.
 ===== Options ===== ===== Options =====
 ==== Active low ==== ==== Active low ====
sensor-int-en.1600423540.txt.gz · Last modified: 2020/09/18 12:05 by rjversluis