User Tools

Site Tools


sensor-int-en

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
sensor-int-en [2018/12/31 15:36]
smitt48 [Note]
sensor-int-en [2021/05/05 01:17] (current)
rainerk [Type]
Line 10: Line 10:
  
 SensorDialog Interface Tab.\\ SensorDialog Interface Tab.\\
-{{:​sensor-int-en.png}}\\+{{:​sensor-int-en.png?500}}\\
  \\  \\
  
Line 24: Line 24:
  
  \\  \\
 +
 +=====RFID=====
 +The 32bit RFID number printed on the Tags. (Leading zeros can be left out.)\\
 +This can be used in combination with __**[[:​arduino:​wio-en#​id-12la|WIO-Drive and an ID-12LA reader]]**__.\\
 +All other addressing, like Node ID and Address, are ignored if the RFID did match. (But an additional fake address makes it possible to check the plan virtually.)\\
 +{{:​wio:​rfid32.jpg?​600}}\\
 +Example of the blue Tag scan:\\
 +{{:​wio:​rfid-index.jpg}} ​
 +<​code>​
 +OWIO     0885 Mobile 18 [BR218] RFID event [12.0.197.167.148] [12953492]
 +OModel ​  5329 trying to match sensor event: [WIO] id=[12.0.197.167.148] 0:0 uidname=[] state=0 code=BR218 regval=0 info=
 +OFBack ​  0796 fb[s18-] state=ON code=BR218 dir=0 val=0 count=5 regval[0]=0
 +</​code>​
  
 =====Bus===== =====Bus=====
Line 67: Line 80:
  
 =====Type===== =====Type=====
-^ Value  ^ Type  ^ Manu ^ Remark ​ ^+|< >| 
 +^ Value  ^ Type  ^ Manufacturer ​^ Remark ​ ^
 | 0 | Current sensors | - | Most commonly used; Can also report bi-directional information;​ Also for Hall Sensors when not used as wheel counters. | | 0 | Current sensors | - | Most commonly used; Can also report bi-directional information;​ Also for Hall Sensors when not used as wheel counters. |
 | 1 | IR Lissy | Uhlenbrock | Can be used with the __**[[:​sensor-gen-en#​timer|Off timer]]**__ to get it unoccupied. | | 1 | IR Lissy | Uhlenbrock | Can be used with the __**[[:​sensor-gen-en#​timer|Off timer]]**__ to get it unoccupied. |
Line 74: Line 88:
 | 4 | RailCom | - | Not used; Same as type=0. | | 4 | RailCom | - | Not used; Same as type=0. |
 | 5 | RFID | MERG, LDT | Not used; Same as type=0. | | 5 | RFID | MERG, LDT | Not used; Same as type=0. |
-| 6 | Wheel counter | **[[:​gca173-en|GCA173 ​Hall Sensors]]**, **[[:​mgv141-en|GCA141]]** | Used for wheel or car counting. |\\+| 6 | Wheel counter | **[[:​gca173-en|GCA173]]**, ​**[[:​gca179-en|GCA179]]** and **[[:​mgv141-en|GCA141]]** ​\\ for Hall sensors and Reed contacts. ​| Used for wheel or car counting. |\\
 | 7 | GPS | **[[:​got:​got-en|GamesOnTrack]]** | Using the GPS coordinates on the GPS tab. | | 7 | GPS | **[[:​got:​got-en|GamesOnTrack]]** | Using the GPS coordinates on the GPS tab. |
-| 8 | Register | - | Can be used for __**[[:​turntable-int-en#​position_sensors|Turntable position sensor]]**__. ​(Selectrix based systems) ​ |+| 8 | Register | - | Can be used for __**[[:​turntable-int-en#​position_sensors|Turntable position sensor]]**__. ​ |
  
 Read **[[sensor-bi-directional-en|Bi-Directional Communication]]** for more information on this topic.\\ Read **[[sensor-bi-directional-en|Bi-Directional Communication]]** for more information on this topic.\\
- 
- 
  \\  \\
 +=====Register trigger===== 
 +Specifies the physical quantity for which the value represented by the register bits is defined.
 ===== Options ===== ===== Options =====
 ==== Active low ==== ==== Active low ====
Line 96: Line 109:
  
 =====Note===== =====Note=====
-For the assignment of addresses to sensor\feedback in the track plan, there is help with **[[sensormon-en#​Tip for the assignment of addresses to sensors\feedback in a track plan the|Sensor Monitor]]** \\+For the assignment of addresses to sensor\feedback in the track plan, there is help with **[[sensormon-en#​Tip for the assignment of addresses to sensors\feedback in a track plan|Sensor Monitor]]** \\
  \\  \\
 +
 +
sensor-int-en.1546266987.txt.gz · Last modified: 2018/12/31 15:36 by smitt48