switch-gen-en
no way to compare when less than two revisions
Differences
This shows you the differences between two versions of the page.
— | switch-gen-en [2025/01/30 16:29] (current) – created - external edit 127.0.0.1 | ||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ======General====== | ||
+ | [[: | ||
+ | [[english|Content]] -> [[english# | ||
+ | * [[switch-index-en|Index]] | **[[switch-gen-en|General]]** | [[switch-int-en|Interface]] | [[switch-wiring-en|Wiring]] | [[switch-ctrl-en|Control]] | [[switch-frog-en|Frog]] | [[switch-td-en|Trackdriver]] | [[switch-usage-en|Usage]] | [[switch-menu-en|Menu]] | ||
+ | // \\ // \\ | ||
+ | // \\ // \\ | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | SwitchDialog General Tab.\\ | ||
+ | {{: | ||
+ | \\ | ||
+ | | All text fields which are marked with a **@** can open the __**[[: | ||
+ | |||
+ | \\ | ||
+ | |||
+ | =====ID===== | ||
+ | The ID is used through out the Rocrail program as unique key for referencing this turnout and is therefor very important. | ||
+ | If you change the ID you will likely need to edit the defined routes.\\ | ||
+ | |||
+ | \\ | ||
+ | =====Use Short ID===== | ||
+ | The Short ID is used for showing this switch on a throttle display. It is free text and optional.\\ | ||
+ | The checkbox must be set to enable transferring the short ID to a throttle for this switch.\\ | ||
+ | Activate menu item **" | ||
+ | > **Note:** The transmission is processed together with the __**[[loc-gen-en# | ||
+ | |||
+ | * Supported Apps/ | ||
+ | * __**[[: | ||
+ | * __**[[: | ||
+ | |||
+ | \\ | ||
+ | |||
+ | =====Number===== | ||
+ | This number is used for mapping a switch command by address to this switch.\\ | ||
+ | See __**[[: | ||
+ | |||
+ | \\ | ||
+ | =====Decoder===== | ||
+ | The predefined __**[[: | ||
+ | With __**[[lan-en# | ||
+ | \\ | ||
+ | |||
+ | =====BlockID===== | ||
+ | The __**[[: | ||
+ | The switch will report locked if the block referred by this blockID is not free.\\ | ||
+ | \\ | ||
+ | |||
+ | ===== Route IDs ===== | ||
+ | Route IDs are for showing the locked routes using the **route** representation.\\ | ||
+ | This is a list of comma separated Route IDs without white space (blanks). If one of the IDs has become locked the **route** representation will be shown.\\ | ||
+ | With the […] button a list of Route IDs can be selected.\\ | ||
+ | |||
+ | |||
+ | |||
+ | \\ | ||
+ | |||
+ | =====Locked by===== | ||
+ | Read only field which shows the locking ID if any.\\ | ||
+ | A switch is generelly locked by a Locomotive when it activates a route.\\ | ||
+ | |||
+ | \\ | ||
+ | =====State===== | ||
+ | The current switch position as last reported by the server.\\ | ||
+ | |||
+ | \\ | ||
+ | =====Switched===== | ||
+ | All commands issued under Rocrail control.\\ | ||
+ | This counter can be useful for service intervals.\\ | ||
+ | \\ | ||
+ | ===== Type ===== | ||
+ | Following types are available: | ||
+ | ^ Type ^ Motors/ \\ Coils ^ Remark ^ Symbol/ \\ Positions ^ | ||
+ | | Turnout | ||
+ | | __**[[: | ||
+ | | __**[[: | ||
+ | | ::: | ::: | Crossing (no motor/coil) with option [[# | ||
+ | | ::: | 1 | Double slip switch with one motor like, e.g., Märklin 24624, 2260, 5128. \\ One motor moves all slips, two possible positions \\ \\ Positions: Straight, turnout | Crossing left \\ {{: | ||
+ | | ::: | ::: | Crossing with one motor with option [[# | ||
+ | | Double Crossing | 2 | __Two__ motors moving the slips, max. four positions. \\ __Two addresses__ must be specified! \\ __Not to be used__ for double slip switches with only one motor. These have to be set up as crossings, see above. \\ \\ Positions: Straight, turnout, left, right | Double Crossing left \\ {{: | ||
+ | | Single Crossing | ||
+ | | ::: | ::: | ::: | __SubType right__ \\ Single Crossing left \\ {{: | ||
+ | | Threeway | 2 | __Two__ motors moving the slips, three positions. \\ __Two addresses__ must be specified! \\ \\ Positions: Straight, left, right | {{: | ||
+ | | Decoupler | ||
+ | | Accessory | ||
+ | | Twoway | 1 | Twoway or **[[http:// | ||
+ | |||
+ | \\ | ||
+ | |||
+ | =====SubType===== | ||
+ | For double crossing type with dual motor control to use only a single slip.\\ | ||
+ | Select: Default = Double Slip Switch.\\ | ||
+ | Select: Left or Right = Single Slip Switch. \\ | ||
+ | This reduces the commands to straight, turnout(=diagonal) and __left or right__, i.e from four to three positions.\\ | ||
+ | |||
+ | |||
+ | \\ | ||
+ | |||
+ | =====Accessory# | ||
+ | The symbol number used for type **Accessory** or **Switch**. | ||
+ | * See: __**[[: | ||
+ | * Used if greater then 1 for type Switch. (None Raster.) | ||
+ | |||
+ | |||
+ | \\ | ||
+ | |||
+ | =====Direction===== | ||
+ | Select a left hand or right hand for this turnout or double crossings. Threeways do not have this option. | ||
+ | > | ||
+ | \\ | ||
+ | |||
+ | =====Safe switch position===== | ||
+ | If the switch is unlocked, and Rocrail is running in auto mode, this position will be set after the __**[[rocrailini-automode-en# | ||
+ | This option was originally for switches which needs continues energy in a certain position. To reduce the total needed energy this "Save position" | ||
+ | In the meantime it is mostly used for " | ||
+ | |||
+ | =====Options===== | ||
+ | ====Raster==== | ||
+ | Alignment of switches: | ||
+ | | {{switch-default.png}} | {{switch-raster.png}} | | ||
+ | | default | ||
+ | |||
+ | |||
+ | To create a " | ||
+ | {{: | ||
+ | |||
+ | In order to show the " | ||
+ | {{: | ||
+ | |||
+ | The following Switch Options need to be changed: check the " | ||
+ | Adjust all other tracks accordingly. \\ | ||
+ | {{: | ||
+ | **Note: If the routes that cross this " | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ====Road==== | ||
+ | Instead of the chosen theme for track symbols the road theme is used. | ||
+ | \\ | ||
+ | ====Show==== | ||
+ | The turnout is visible in the plan. | ||
+ | \\ | ||
+ | |||
+ | ====Show ID==== | ||
+ | Active (default): The switch ID is shown in the track plan (only if the client is set to show IDs, e.g. Rocview: **[[: | ||
+ | Deactivated: | ||
+ | |||
+ | ====Rectangular==== | ||
+ | Motor-less 90° [[: | ||
+ | \\ | ||
+ | |||
+ | ====Swap straight==== | ||
+ | If the switch symbol is logically swapped this option will be used for the __**[[: | ||
+ | |||
+ | ====Put out of operation==== | ||
+ | This option prevents the switch being used. Routes over this switch cannot be set.\\ | ||
+ | The background will turn to grey.\\ | ||
+ | |||
+ | ====Operable==== | ||
+ | To prevent manual operation by clients.\\ | ||
+ | |||
+ | ====Start of Day (SoD)=== | ||
+ | Include the initialization of this turnout by SoD.\\ | ||
+ | |||
+ | ====Exclude from Routing==== | ||
+ | Activate when the Router should not define commands in routes for this turnout.\\ | ||
+ | \\ | ||
+ | |||
+ | ====Static==== | ||
+ | The switch cannot be set in another position, and can only be used in the actual position in automatic mode.\\ | ||
+ | If the option is activated, the symbol background is displayed in " | ||
+ | |||
+ | * **Tip:** The option is also available in the __**[[: | ||
+ | |||
+ | ====Manual operated==== | ||
+ | Manual operated switches will be locked for routes, but if they are not in the wanted position, the loco/train will wait until they are set manually in the wanted position.\\ | ||
+ | The switch must be in the wanted position before the route is locked if the ' | ||
+ | |||
+ | =====Actions===== | ||
+ | See [[: | ||
+ | |||
+ | * **Note:** If the action parameter is set to " | ||
+ | |||
+ | \\ | ||
switch-gen-en.txt · Last modified: 2025/01/30 16:29 by 127.0.0.1