This is an old revision of the document!
Table of Contents
WIO Control
| Travail en cours |
Le Contrôle WIO est basé sur le Module Dev ESP32 et les cartes LOLIN D32.
Afficheur
Le Contrôle WIO nécessite un afficheur pour certaines de ses fonctions:
- Barre de statut
- Sélection de locomotive
- Sélection de fonction
- Mode Automatique locomotive (Affiché dans l'icône de connexion au serveur.)
Programmation
ESP32 Dev Module
The Boot button must be pressed to be able to flash this module over USB.
This button is located right beneath the display.
The following error will show up in the Arduino IDE if this button is not pressed:
Connecting........_____....._____....._____....._____....._____....._____....._____....._____....._____....._____ A fatal error occurred: Failed to connect to ESP32: Timed out waiting for packet header
Pinout
| ESP32 Dev Module | LOLIN D32 |
|---|---|
 |  |
Extended Layout
The ESP32 type board selection is set by WIO Dialog.
| Preliminary |
|---|
Compared with the ESP8266, the ESP32 has a lot more I/O Pins, so an extra F0 and Shift button are added.
| GPIO Dev Module | GPIO Lolin D32 | Function | Selection mode | Shift function | Long click | Long click + shift |
|---|---|---|---|---|---|---|
| 26 | 26 | Rotary V+ | Browse loco list down / Select function right | - | - | |
| 25 | 25 | Rotary V- | Browse loco list up / Select function left | - | - | |
| 36 | 34 | Rotary direction | Take over the selected loco from the list / Flip selected function | - | - | |
| 27 | 27 | F0 | - | Alter between loco 1 and 2 | Power off | Power on |
| 32 | 32 | F1 | - | F9 | F5 | F13 |
| 33 | 33 | F2 | - | F10 | F6 | F14 |
| 0 | 0 | F3 | - | F11 | F7 | F15 |
| 14 | 14 | F4 | - | F12 | F8 | F16 |
| 13 | 12 | Shift | - | - | Function selection mode | - |
| 16 | 5 | LED | - | - | - | - |
| 35 | 35 | Battery (ADC) | - | - | - | |
| 21 | 21 | SDA (Display) | - | - | - | - |
| 22 | 22 | SCL (Display) | - | - | - | - |
Note: Do not use a hardware pull-up resistor on GPIO12 because this will block uploading firmware by USB.
ESP32 Dev Module
Voltage divider
A voltage divider is needed to measure the Lipo(battery).
GPIO35 is connected to the Lipo + with 47k resistor, and with a 100k resistor to the ground(GND).
NoGo Pins
The following pins can not be used:
- GPIO06 - GPIO11 (Are in use by the Flash interface.)
- GPIO12 can only be used as output. If the pin is pulled up at boot time, the ESP32 won't boot/flash.
LOLIN D32
Voltage divider
The LOLIN D32 has a build in divider on GPIO35: 100k/100k.
See: https://wiki.wemos.cc/_media/products:d32:sch_d32_v1.0.0.pdf
I2C Display
The I2C SSD1306 compatible 128*64 display, must be connected to GPIO21(SDA) and GPIO22(SCL).
Short IDs
Use Transmit short IDs to load the locomotive short IDs into WIO Control.
Selecting a locomotive
- Press and release the shift button; On the bottom display line the first ID is shown.
- Turn the rotary until the wanted locomotive is selected.
- Push the rotary button to activate the selected locomotive.
Just press and release the shift again to cancel the selection procedure.
Hardware
A fitting case could be:
Schematic and PCB
| WIP |